Gemini DJ MPX-40 Mode D'emploi page 6

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

Press C

(9) to pause the song at your point of cue. Press & hold

the C

(9) button to begin Cue preview, which will allow you to

judge whether the point of cue you have loaded is satisfactory.

If you are not satisfied with your point of cue, enage P

use the J

(22) to find the exact point you wish to begin

HEEL

play. Rapidly press P

(8) twice to enter & exit play mode.

LAY

AUSE

You will be in pause mode. The C

(9) LED will blink. Repeat the

steps for Cue preview, to make sure your new cue point is satisfac-

tory.

When you are satisfied with your point of cue, leave the C

button alone, the C

(9) LED will remain on to indicate that the

point of cue is stored & ready to be used.

CUE IDENTIFICATION:

The MPX-40 have the ability to store one cue point per track in the

internal memory. This enables the DJ to scan quickly to a starting

point for easier mixes during a live session.

To store this cue point follow the steps to store a cue point.

Once you are satisfied with your cue point, press & hold the

(12) button for two seconds in order to store this cue

EMO

TORE

point. If you are not satisfied with this cue point repeat the steps to

store a cue point.

Your cue is now saved & can be recalled at any moment long after

you have stopped playing with this CD. You will notice the LCD (16)

will flash with the cue point memory position once this cue point has

been saved successfully.

The cue point has now been stored in the memory of the MPX-40

and can be recalled at any moment. You will notice the A

LED blinking indicating that the MPX-40 recognize a stored cue

point on the CD. Simply scroll to any track that has a cue point

stored. Press and hold the Folder/Recall Cue (23) knob untill the

point has appeared on the LCD screen. Press play & the song will

start from the stored cue point.

SEAMLESS LOOP:

Press the L

(17) button to enter an entry point into

OOP

the memory, & the L

's (17) green LED will blink rapidly

OOP

while memorizing the loop entry point into the memory.

___________________________________________________________________________________________________________________________________________________________________

After an entry loop point is memorized, press L

play mode to complete the loop. The unit will automatically repeat

the section between the loop's entry point, programmed with the

pressing of the L

(8) &

OOP

AUSE

when the L

(18) button is pressed. The loop is now pro-

OOP

grammed into the unit's memory.

While playing the loop, both the L

green LEDs will blink to indicate that the loop is in use. You will

notice the LCD (16) will also indicate that the L

blinking C

-B icon that will remain steady once the loop has been

(9)

stopped.

Press the R

(19) for the unit to return to the previously set

ELOOP

loop. Press the R

(19) repeatedly for stuttering the loop entry

ELOOP

point. The R

(19) function automatically returns the music to

ELOOP

the loop point & will play the loop until it is released with the L

(18) button.

Press the B-E

(20) button to edit the loop created by your

DIT

. When pressing B-E

EAMLESS

OOP

read the frame where the L

with the use of the J

right examining frame by frame while the loop repeats itself. You

should be able to hear the difference in each frame until you are sat-

isfied with your loop exit point. Press B-E

isfied with your exit point & your loop will continue to play until you

press L

(18).

OOP

To exit the loop & resume play, press L

loop & continue play from the point where the loop ends.

UTO

SLEEP MODE:

The MPX-40 feature a default S

when the unit recognizes that it has not been in use for some time.

This feature simply shuts O

the unit's playing capabilities. You will notice the LCD (16) reads

when this mode is activated. To deactivate this default mode,

LEEP

begin play & the unit will "wake up" to play music once again.

TROUBLESHOOTING:

· If the disk will not play, check to see if the disc was loaded cor-

(18) in

OOP

(17) button, & a second exit loop point,

(17) & L

(18)

OOP

is in use with a

OOP

(20), the LCD (16) will

DIT

(18) is set. You may adjust it

OOP

(22), by turning the wheel left or

HEEL

(20) when you are sat-

DIT

(18) to stop the

OOP

mode that activates itself

LEEP

the laser to increase the longevity of

NOTES:

rectly (label side up). Also check the disc for excessive dirt, scratch-

es, etc.

· If the disc turns but there is no sound, check the cable connec-

tions. If they are okay, check your amplifier or receiver.

· If the CD skips, check the CD for dirt or scratches. Do not

assume that the CD player is defective. Many CDs are recorded out

of spec & will skip on most or all CD players. Before sending the

unit in for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:

ENERAL

Type........................................Single Mechanism Compact Disc Player

Disc Type...................................Standard Compact discs (12cm, 8cm)

Time Display.............Track Elapsed, Track Remain, or Total Remain

Variable Pitch..........± 4%, ± 8%, ± 16%, + 100% Slider with Resume Switch

Pitch Bend......................................................................± 4% Maximum

Instant Start..........................................................Within 0.015 seconds

Track Selection..............................................................1 to 99 Tracks

Dimensions......................................8 1/2" W x 3 3/4" H x 12 1/2" D

................................................................................(216 x 95 x 320 mm)

Weight.............................................................Player Unit 6.62 lbs (3 kg)

UDIO

ECTION

Audio Types..............................................................................CD, MP3

Quantization..........................1 Bit Linear/Channel, 3 Beam Laser

MP3/CD Bit Rate...............................................................32-320KBPS

Oversampling Rate......................................................................8 Times

Sampling Frequency...................................................................44.1 kHz

Frequency Response.....................................................20 Hz to 20 kHz

Total Harmonic Distortion.......................................Less Than 0.05%

Signal to Noise Ratio.......................................................................90 dB

Dynamic Range...........................................................................< 80 dB

Channel Separation...........................................................88 dB (1 kHz)

Output Level..................................................................1.3 Volts R.M.S.

Power Supply..................................................AC 115/230 V, 60/50 Hz

PECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION

FOR IMPROVEMENT

Table des Matières

Gemini DJ MPX-40 Mode D'emploi page 6

Les langues disponibles

Manuels Connexes pour Gemini DJ MPX-40

Produits Connexes pour Gemini DJ MPX-40

Table des Matières