Accessories - Milwaukee M12 205 Serie Manuel De L'utilisateur

SPECIFICATIONS
Cat. No. ................................................. 205 Series
Battery Controller ................................43-72-1000
Volts...............................................................12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
FUNCTIONAL DESCRIPTION
3
2
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Inserting/Removing the Battery
To insert the battery, slide the pack into the body of
the battery controller. Make sure it latches securely
into place.
Insert the power cable (from inside the pocket) into
the power cable port on the battery controller.
Push the power cable completely into the battery
controller pocket and zip all pockets closed.
To remove the battery, push in the release buttons
and pull the battery pack away from the controller.
OPERATION
The power button is located on the upper left side of
the heated gear, inside on some models.
To turn on, press and hold (about 2 seconds) the
power button. The core (upper chest) and secondary
(lower chest) zones will be turned to High and the
LEDs will light.
Temperature setting can be adjusted at any time
by pressing the power button. Each press will cycle
through the temperature settings.
To turn off, press and hold (about 2 seconds) the
power button. The LEDs will turn off.
If the heated gear turns off unexpectedly, check
connections and charge the battery pack. Battery
controller is located inside of pocket.
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack and battery controller from the
heated gear before performing any maintenance.
Never disassemble the heated gear, battery pack
or charger. Contact a MILWAUKEE service facil-
ity for ALL repairs.
1
1. Power button
2. Battery controller pocket
3. Power cable
CARE
If the heated gear does not start or operate properly
with a fully charged battery pack, clean the contacts
on the battery pack. If the heated gear still does not
work properly, return the heated gear, charger and
battery pack, to a MILWAUKEE service facility for
repairs.
To reduce the risk of personal in-
WARNING
jury and damage, disconnect and
remove battery pack and battery controller from
battery controller pocket before washing. Never
immerse your battery controller, battery pack, or
charger in liquid or allow a liquid to flow inside
them.
To clean the heated gear:
1. Remove battery pack and battery controller.
2. Push the power cord completely into the battery
controller pocket and fasten closed. Zip center
front zipper closed before washing.
3. Machine wash, Gentle Cycle in warm water. Do
not use bleach. Do not dry clean. Do not wring or
twist.
4. Tumble Dry on Low Heat. Do not iron.

ACCESSORIES

Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE HEATED GEAR product (including its battery holder/
controller) is warranted to the original purchaser only to be free from defects
in material and workmanship. Subject to certain exceptions, MILWAUKEE
will repair or replace any part on a Heated Gear product which, after
examination, is determined by MILWAUKEE to be defective in material or
workmanship for a period of one (1) year* after the date of purchase. Return
of a Heated Gear product to a MILWAUKEE factory Service Center location,
freight prepaid and insured, is required. A copy of the proof of purchase
should be included with the return product. This warranty does not apply to
damage that MILWAUKEE determines to be from repairs made or attempted
by anyone other than MILWAUKEE personnel, misuse, alterations, abuse,
normal wear and tear, or accidents.
*This warranty does not cover a M12™ LITHIUM-ION Battery Pack, a M12™
Charger, or a REDLITHIUM™ USB battery; there are separate and distinct
warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty on
MILWAUKEE Heated Gear products. The manufacturing date of the product
will be used to determine the warranty period if no proof of purchase is
provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT
FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO
NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE
PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,
OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR
DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO,
FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT
LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES
3
(1.800.729.3878)