Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2.2.3
Clothing and equipment
•
Always wear adequate and suitable safety clothing for the work to be carried out. Make sure that your clothes are
tight fitting to the body. Avoid wearing neckties, necklaces, belts or long hair not tied as they can be caught be-
tween the moving parts. Use non-slip shoes, heavy-duty gloves,
protective goggles or a visor, safety footwear and noise-abatement earmuffs.
2.2.4
Workplace safety
•
Only use the tool in good visibility conditions. A dimly lit working area may cause accidents. Do not perform cuts in
poor light conditions, like in the dark in closed or open environments, at night, at dusk, at dawn or with dust or sand
in the air impeding clear visibility below 2 metres. Place the product at a distance of 2 metres and check if you are
able to clearly read the labels.
•
Do not use the tool in an explosive, flammable or damp environment.
•
Keep children, observers or animals at a safe distance before activating the tool in order to avoid hazards or inju-
ries. When determining the safety distance, evaluate the risk of branches being flung towards persons, objects or
animals. The appropriate safety distance in normal tension conditions is 5 metres from the end of the branches.
2.2.5
Electrical safety
•
Before, during and/or after use, do not expose the tool to damp environments, water or any other humid conditions,
in order to prevent electric shocks or short circuits.
•
Keep the tool away from heat sources, oil, solvents, sharp edges or moving parts.
•
Do not expose the tool to rain. Keep it in a dry place.
•
Liquid leaking from the battery pack can harm the operator. Do not touch any liquid from the battery pack. In case of
contact, rinse immediately with clean water. If the liquid comes into contact with your eyes, rinse thoroughly with
clean water and immediately seek medical attention.
CAUTION!
Read the following instructions carefully. Failure to do so can result in electric shock, fire or serious damage.
2.3
Use Warnings
2.3.1
Warnings on the use of the tool
•
Never use the tool if it is damaged, wrongly regulated or only partially assembled.
•
Get into a stable and safe working position, which guarantees perfect balance (for example a flat and dry surface).
•
Do not use the tool if the ON/OFF button (9) is not working properly.
•
Use the tool, accessories, etc. in compliance with these instructions and considering the working conditions and
operations to be performed.
•
Always check that the safety and protection devices are working properly.
•
Before starting the tool, check that the chain (1) is not touching any foreign bodies.
•
Always keep the motor at high speed when cutting.
•
Be very careful when cutting bushes or small shrubs, since soft parts may get entangled in the chain (1) and be
thrown against the operator, or cause them to lose balance.
•
Be very careful with the grip (10), which should be always perfectly dry, clean and free from oil residues.
•
Keep the bar (2) and chain (1) clean and sharp.
•
Do not use the tool while standing on a ladder.
•
Never cut branches which are close to electric wires.
•
Do not touch the chain (1) when it is rotating.
•
Pay attention to any kickback and recoil movements of the bar (2). They may cause the operator to lose their bal-
ance or control of the tool.
•
Pay attention when cutting branches under tension, since they may cause loss of control of the tool.
•
Pay attention to any kickback and recoil movements of the bar (2). They may cause the operator to lose their bal-
ance or control of the tool.
•
Pay attention when cutting branches under tension, since they may cause loss of control of the tool.
•
Inhaling atomised oil and/or wooden dust may cause irritation or intoxication of the operator's breathing system. In
case of prolonged ailments, consult a competent doctor.
•
Never get distracted. Check what you are doing and use common sense when using the tools.
Use and maintenance manual – Instructions
Original instructions Rev.: 00, Date 11/04/2022
Page 33
Publicité
Table des Matières
