Purpose Of This Manual; Safety Information - Battipav EXPERT 400 Mode D'emploi

Battipav srl

PURPOSE OF THIS MANUAL

This manual is an integral part of the machine. It was produced by BATTIPAV S.R.L. to provide those authorised to work with the
machine with the information required for its foreseeable lifespan. Before starting to use this machine read the safety chapter
carefully. Each machine is subjected to a series of tests and carefully checked before leaving our factory. BATTIPAV S.R.L. is
constantly striving to develop their machines and therefore reserves the right to make any change without prior notice. Therefore,
no claims may be made on the basis of the data and illustrations contained in this manual.

SAFETY INFORMATION

• The manufacturer accepts no responsibility where the EXPERT cutter is used with any tools other than those specified in the
"RECOMMENDED USE" paragraph.
DO NOT USE WOODEN DISCS. DO NOT USE DRY-CUTTING DISCS.
• EXPERT is made to operate exclusively under the conditions indicated under "TYPE OF OPERATION ALLOWED", in the
"RECOMMEDED USE" paragraph.
• During cutting operations, allow the machine to rest as indicated.
• EXPERT is not made for use with a continuous load.
• This machine is designed to use Ø 500 and/or Ø 600 mm discs. For discs with diameters of more than a few millimetres, it may be
necessary to lock the motor head in a slightly raised position in order to avoid interfering with the working surface during cutting.
DO NOT USE DIAMOND TIPPED DISCS OF LOW QUALITY OR THAT ARE NOT SUITABLE FOR THE
SPECIFIC USE FOR WHICH THE MANUFACTURER SUPPLIED THEM. THE USE OF POOR QUALITY DISCS
CAN HARM THE OPERATOR AND DAMAGE THE MACHINE, AS WELL AS SIGNIFICANTLY SLOWING THE
WORK. THE MACHINE IS NOT INTENDED FOR USE IN AN EXPLOSIVE ENVIRONMENT. ALWAYS USE
INDIVIDUAL PROTECTION DEVICES TO REDUCE THE RISKS CAUSED BY WORK. NEVER START THE
MACHINE WHEN THE CUTTING TOOL IS MOVING; WAIT FOR IT TO STOP. TO REDUCE THE RISKS ARISING
FROM FRAGMENTATION OF MATERIALS, ALWAYS USE APPROPRIATE PROTECTIVE GOGGLES. THE
CONTINUOUS USE OF THE MACHINE FOR 8 (EIGHT) HOURS CAUSES EXPOSURE TO NOISE OF OVER 85
DB(A). THEREFORE IT IS NECESSARY TO WEAR APPROPRIATE NOISE PROTECTION EARMUFFS AS SET
DOWN BY LAW. TO REDUCE RISKS CAUSED BY ACCIDENTAL CONTACT WITH THE CUTTING TOOL, USE
CUT-RESISTANT PROTECTIVE GLOVES COMPLIANT WITH DIRECTIVE EN388.
Each time the machine is connected to the power supply, check the correct direction of rotation of the motor
indicated on the disk protection. ALWAYS PERFORM THE ROTATION DIRECTION VERIFICATION OPERATION
400V
WITH DISASSEMBLED CUTTING DISC. DO NOT USE THE MACHINE FOR ANY REASON WITH THE DIRECTION OF
/3F
ROTATION CONTRARY TO THAT INDICATED.
Warning! When using electric tools, following safety precautions should always be followed to reduce the risk of fire, electric shock
and personal injuries. Read and follow all these instructions before attempting to operate this product and save them with care!
Keep your work area perfectly clean
• Cluttered areas invite injuries.
Consider work area environment
• Don't expose tools to rain.
• Don't use tools in damp or wet locations. Keep work area well lit.
• Don't use tools in presence of flammable liquids or gases.
Guard against electric shocks
• Prevent body contact with grounded surfaces.
Keep children away!
• Do not let third parties contact tool or extension cord. All visitors should be kept away from work area.
Store your tools in a save place
• When not in use, tools should be stored in dry and save places, out of the reach of children.
Don't force tool
• It will function better and in a safer way at the rate for which it was intended.
Use the right tool
• Don't use low duty tools or accessories to do the job of a heavy-duty tools. Don't use tools for purposes not intended.
Dress properly
"TRANSLATION OF THE ORIGINAL INSTRUCTIONS"
SAVE THESE INSTRUCTIONS WITH CARE.
GB
41