Electrical Grounding Instructions - F.Bertazzoni KO30 PRO X Instructions D'installation

INSTALLATION INSTRUCTIONS
UNPACkINg ANd exAMININg
YOUR OveN
Open the bottom of the carton, bend the carton flaps back and
tilt the oven over to rest on plastic foam pad. Lift carton off
oven and remove all packing materials, Wall and Top Cabinet
Template, Turntable, and Turntable Support. sAve THe
CARTON As IT MAY MAke INsTAllATION eAsIeR.
• Remove the feature sticker from the outside of the door, if
there is one.
• dO NOT ReMOve THe wAvegUIde COveR, which is
located on the right side wall of the oven cavity. Check to
see that there is a Wall TEMPLATE and Top CABINET
Template. Read enclosures and SAVE the Use and Care
manual.
Check the oven for any damage, such as misaligned or bent
door, damaged door seals and sealing surfaces, broken or
loose door hinges and latches and dents inside the cavity or
on the door. If there is any damage, do not operate the oven
and contact your dealer or BERTAzzONI AUTHORIzED
SERVICER.
MOUNTINg sPACe
This over the range microwave requires a mounting space on
a wall as shown in Figure 1. It is designed to be used under
standard 12" wall cabinets.
12"
30"
15.5"
Backsplash At least 2"
Figure 1
This over the range microwave should be mounted against
and supported by a flat vertical wall. The wall must be flat for
proper installation. If the wall is not flat, use spacers to fill in the
gaps. Wall construction should be a minimum of 2" x 4" wood
studding and 3/8" or more thick dry wall or plaster/lath. The
mounting surfaces must be capable of supporting a weight of
110 pounds—the oven and contents—AND the weight of all
items which would normally be stored in the top cabinet above
the unit. The unit should be attached to a minimum of one 2"
x 4" wall stud.
To find the location of the studs, one of the following methods
may be used:
• Use a stud finder, a magnetic device which locates the
nails in the stud.
• Use a hammer to tap lightly across the mounting surface
to find a solid sound. This will indicate stud location.
The center of the stud can be located by probing the wall with a
small nail to find the edges of the stud and then placing a mark
halfway between the edges. The center of any adjacent studs
will normally be 16" or 24" to either side of this mark.
eleCTRICAl gROUNdINg
This appliance must be grounded. This oven is equipped with
a cord having a grounding wire with a grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and
local codes and ordinances. In the event of an electrical short
circuit, grounding reduces risk of electric shock by providing an
escape wire for the electric current.
36" or
wARNINg – Improper use of the grounding plug can result in
more from
a risk of electric shock.
cooking
surface
eleCTRICAl ReqUIReMeNTs
The oven is equipped with a 3-prong grounding plug. DO NOT
72" or more
UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE
from floor
GROUNDING PIN FROM THE PLUG.
dO NOT Use AN exTeNsION CORd. If the power supply
cord is too short, have a qualified electrician or serviceman
install an outlet near the appliance.
The Power Supply Cord and plug must be connected to a
separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit,
single grounded receptacle. The receptacle should be located
inside the cabinet directly above the over the range microwave
mounting location as shown in figure 2.
NOTe:
• If you have any questions about the grounding or
electrical instructions, consult a qualified electrician or
serviceperson.
E2
wAll CONsTRUCTION
INsTRUCTIONs