Cequent Performance Products 24926 Instructions D'installation

Frame rail
Fascia
Vehicle forward
Hitch Shown In Proper Position
Equipment Required: 7/16" Pull wire (Provided)
& Sealant
Fastener Kit: 24926F
Wrenches: Torx® 25, 10mm, 13mm,
17mm, 19mm, 11/16, & 3/4"
Drill Bits: None
Exhaust not shown.
Figure 2.
Kink Pull wire to keep
spacer independent of bolt
Figure 3.
Note: sort hardware prior to hitch installation to confirm
conical washer are kept with coordinated with bolts.
1 1 1 1
Qty. (1) Hex Bolt M12X1.25X30 CL8.8
2 2 2 2
Qty. (2) Conical washer 1/2"
3 3 3 3
Qty. (1) Handle nut M12
4 4 4 4
Qty. (1) Carriage bolt 7/16-14X2.00 GR5
5 5 5 5
Qty. (1) Spacer .250X1.00X3.00
6 6 6 6
Qty. (1) Conical Washer 7/16"
7 7 7 7
Qty. (1) Hex nut 7/16-14
8 8 8 8
Qty. (2) Hex bolt M8X1.25X30 CL8.8
9 9 9 9
Qty. (2) Conical washer 3/8"
Qty. (1) Carriage bolt 1/2-13X2.00 GR5
Qty. (1) Spacer (egg shape)
Qty. (1) Hex nut 1/2"
Qty. (9) Flat washer 5/16"
Qty. (1) Spacer, .437 X 1.0 X 2.0
Tighten all M8 CL8.8 fasteners with torque wrench to 20 Lb.-Ft. (27N*M)
Tighten all 7/16-17 GR5 fasteners with torque wrench to 50 Lb.-Ft.(68 N*M) Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2014 Cequent Performance Products, Inc
Installation Instructions
Volkswagen Jetta
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Seal the hole in the trunk pan to
prevent intrusion of exhaust
fumes and water.
Exhaust
hanger
bracket
2
9
Seal existing drain holes
8
in trunk pan to prevent
intrusion of exhaust
fumes and
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Figure 1.
Fuel vapor
water.
canister
Remove the spare tire from the spare tire carrier inside of the trunk. Remove the
vehicle forward rubber isolator from the trunk pan and install the fasteners (Item 10 &
11) through the trunk pan. Return plug to vehicle owner.
Remove plastic fascia covering from underneath the passenger side of the vehicle by
removing the (3) Torx 25 screws and (2) plastic hex nuts. Return plastic fascia
covering to vehicle owner.
Lower the exhaust by removing (2) bolts from the exhaust hanger bracket and the
rubber exhaust isolator ahead of the axle. Support as required. Return bolts to
owner.
Lower the Fuel vapor canister on the passenger side (if present).
Using the pull wire, feed the 7/16 carriage bolt and spacer(item 4 & 5), through the
access slot in the frame rail on the passenger side leave the pull wire attached. See
Figure 3. Bend the handle nut and insert into passenger side frame rail over center
hole location.
Raise hitch into position. Push the 7/16 carriage bolt (only) with pull wire attached
into the frame rail. Attach spacer(item 14) to the wire and pull the wire through
passenger side bracket and raise passenger side into position. See Figure 2 . Pull
7/16 carriage bolt through spacer and side bracket and install fasteners loosely.
Install M12 bolt into handle nut loosely. See Figure 1.
Rotate the exhaust bracket forward out of the way and raise the hitch into place on
drivers' side. Pull the exhaust bracket back into place and install the M8 X 1.25 X 30
bolt and 3/8" conical washer through the slots on the exhaust hanger bracket.
Install ½-13 hex nut and spacer onto item 10 & 11 already installed in trunk pan as
shown. Use a sealant (not provided) to prevent exhaust and water from entering.
Seal the hole inside the trunk pan to prevent intrusion of exhaust fumes and water.
Tighten all fasteners to specification.
Reinstall the Fuel vapor canister if lowered in step 4. Use (3) 5/16" flat washers to
space the canister down, re-use the original M6 bolts.
Reinstall the exhaust at the forward isolator, removed in step 1.
Reinstall spare tire, removed in steps 1.
Tighten all M12 CL8.8 fasteners with torque wrench to 70 Lb.-Ft.(95N*M)
Sheet 1 of 3
Printed in Mexico
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Accessory Rating
Wiring Access Location: PC3, 4
5
4
3
Top view of passenger frame rail
24926N 10-31-14
Form F206 Rev B 9-17-2012
24926
60364
77312
A
3
Access
slot
6
7
2
1
Rev. A