Cleaning Floors - POLTI Vaporetto SMART 40 MOP Manuel D'instructions

4. CLEANING FLOORS

Before using the appliance on delicate surfa-
ces, ensure that the part in contact with the
surface is free from foreign bodies that
could cause scratches.
4.1 Make sure that Chapter 1 has been fol-
lowed and connect the accessories as indica-
ted in Chapter 2.
4.2 Connect the extension tubes to the steam
hose and the floor brush to the extension tu-
bes.
4.3 Attach the supplied cloth to the floor bru-
sh. To make it easier to attach, the cloth has
an easy lock/release system to avoid having
to bend over and use your hands. Just place
the cleaning side of the cloth on the floor and
rest the brush on top (11).
4.4Adjust the intensity of the steam by tur-
ning the adjustment knob (7); for this type of
surface we recommend Medium level steam.
4.5 Deactivate the steam lock (4) and continue
with steam delivery, pressing the steam trigger
on the handle of the steam hose (4).
4.6 Clean the floors by moving the brush.
The brush has a flexible joint that makes it
possible to easily reach the most difficult-to-
reach areas (under furniture, under beds,
etc.).
The brush has bristles built into the rear side
(12) ideal for removing the most stubborn dirt.
To use, return the handle to the vertical posi-
tion locking the brush, then tilt until the bru-
shes are touching the floor and scrape off the
dirt.
Before removing the cloth from the brush,
wait a few minutes to allow the cloth to cool.
After which, rest a foot on the tab of the
cloth sticking out and pull the brush upward.
WARNING: Do not
without the cloth.
WARNING: For additional safety, test steam
delivery on a hidden part, leave the steamed
part to dry to ensure that no changes in co-
lour or deformations have occurred.
use the appliance
| 27 |
5. CLEANING CARPETS AND RUGS
WARNING: Before cleaning fabrics with
steam, consult the manufacturer's instruc-
tions and always carry out a test on a hidden
part or on a sample of the material. Allow
the steamed part to dry to make sure that
no changes in colour or deformations have
occurred.
5.1 Make sure that Chapter 1 has been fol-
lowed and connect the accessories as indica-
ted in Chapter 2.
5.2 Connect the extension tubes to the steam
hose and the floor brush to the extension tu-
bes. Insert the brush with the cloth attached
(see point 4.3) in the special frame for sliding
on rugs (13).
5.3 Adjust the intensity of the steam by tur-
ning the adjustment knob (7); for this type of
surface we recommend Medium level of steam.
5.4 Deactivate the steam lock (4) and continue
with steam delivery, pressing the steam trigger
on the handle of the steam hose (4).
5.5 Pass the floor brush over the surface.
Before removing the cloth from the brush,
wait a few minutes to allow the cloth to cool.
After which, remove the frame by resting
the foot on the relative symbol and then re-
move the cloth by holding it firm with the
foot resting on the tab and pulling the brush
up.
6. CLEANING GLASS, WINDOWS
AND TILES
WARNING: To clean glass surfaces during
cold weather, preheat the windows starting
to vacuum from a distance of about 50 cm
from the surface.
6.1 Make sure that Chapter 1 has been fol-
lowed and connect the accessories as indica-
ted in Chapter 2.
6.2 Adjust the intensity of the steam (7) with
the special handle; for this type of surface we
recommend Medium level of steam.
6.3 Ensure that the steam lock on the handle
is deactivated (4).
6.4 To clean windows and mirrors, steam the
surface thoroughly to dissolve the dirt. Con-
nect the small brush with window cleaner to
the flexible hose and go back over the surface
to remove the dirt, without dispensing steam.