Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: Metal file,
Pullwire (provided)
Fastener Kit: 36419F
Wrenches: 11/16
1
Drill Bits: None
2
Existing holes
to be modified
3
4
Note:
Fasteners typical
both sides.
1 1 1 1
Qty. (4)
Carriage Bolt 7/16-14 X 1.25
2 2 2 2
Qty. (4)
Spacer
1.
Detach both (2) rear rubber muffler hangers to lower exhaust.
2.
Enlarge either hole on bottom of both frame rails with a metal file enough to get spacer through.
3.
Feed the pullwire through the newly enlarged hole, attach spacer and bolt and feed one at a time into the frame rail. Leave the
pullwire attached. Repeat on both frame rails as shown in Figure 2.
4.
Feed the second spacer and bolt thru the enlarged hole and back out as shown in Figure 3. Leave the pullwire attached.
Repeat on both frame rails.
5.
Feed the pullwires through the slot on the hitch brackets. Raise the hitch into position being careful not to push the fasteners
into the frame rails.
6.
Attach remaining fasteners as shown Figure 1. Hand tighten only.
7.
Check to assure hitch is centered on vehicle.
8.
Tighten all fasteners to torque specifications.
9.
Reattach rubber muffler hangers.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2015 Cequent Performance Products - Printed in Mexico
Installation Instructions
(Sold separately)
Fascia
Drawbar Kit:
36061
Drawbar must be used in the
Rise position only.
Exhaust hanger
Exhaust not
shown for clarity
Figure 1.
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Mazda CX-7
Do Not Exceed Lower of Towing Vehicle
3500 LB, (1589 Kg) Max Gross Trailer Weight
300 LB, (136 Kg) Max Tongue Weight
Wiring Access Location: SUV3, SUV4
Frame rail
3 3 3 3
Qty. (4)
Conical Washer
4 4 4 4
Qty. (4)
Nut 7/16-14
Sheet 1 of 3
36419N
Part Numbers:
Manufacturer's Rating or
Enlarged hole
Kink pullwire to
Figure 2.
keep spacer
Example of
independent of bolt
pullwire procedure
Figure 3.
10-19-15
Form: F205 Rev A 5-6-05
36419
90154
06401
Frame rail
Rev. B
Publicité
Manuels Connexes pour Cequent Performance Products 36419
Sommaire des Matières pour Cequent Performance Products 36419
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2006, 2015 Cequent Performance Products - Printed in Mexico Sheet 1 of 3 36419N 10-19-15 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2006, 2015 Cequent Performance Products s - Imprimé au Mexique Feuille 2 de 3...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2006, 2015 Cequent Performance Products - Impreso en México Hoja 3 de 3...