Intended Use - Makita DTW300 Manuel D'instructions

Boulonneuse sans fil
Masquer les pouces Voir aussi pour DTW300:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening capacities
Square drive
No load speed (RPM)
Impacts per minute
Overall length
Rated voltage
For use near high-voltage electrical power lines
Net weight
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
Specifications may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for fastening bolts and nuts.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DTW300
Sound pressure level (L
Sound power level (L
) : 108 dB (A)
WA
Uncertainty (K) : 3 dB (A)
Model DTW301
Sound pressure level (L
Sound power level (L
) : 108 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTW302
Sound pressure level (L
Sound power level (L
) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Standard bolt
High tensile bolt
Max impact mode
Hard impact mode
Medium impact mode
Soft impact mode
Max impact mode
Hard impact mode
Medium impact mode
Soft impact mode
) : 97 dB (A)
pA
) : 97 dB(A)
pA
) : 94 dB(A)
pA
DTW300
DTW300XV
DTW301
12.7 mm
144 mm
-
1.5 - 1.8 kg
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH / DC18WC
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
4 ENGLISH
DTW301XV
DTW302
M10 - M20
M10 - M16
9.5 mm
-1
0 - 3,200 min
-1
0 - 2,600 min
-1
0 - 1,800 min
-1
0 - 1,000 min
-1
0 - 4,000 min
-1
0 - 3,400 min
-1
0 - 2,600 min
-1
0 - 1,800 min
138 mm
D.C. 18 V
-
-
1.4 - 1.8 kg
DTW302XV

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dtw300xvDtw301Dtw301xvDtw302Dtw302xv

Table des Matières