Publicité
Les langues disponibles
Les langues disponibles
11. & 12. Line Out XLR and Lift/GND Button
The Line Out allows the user to connect the Small Block preamp directly to a mixing console
when performing live or recording in the studio. Use a standard XLR mic cable, or an XLR
female to a 1/4-inch TRS patch cable, depending on the mixer's available inputs (it is usually
best to use a 1/4-inch TRS line-level input on the board to match gain levels). In the Lift
setting, the button disconnects Pin 1 of the XLR to help reduce ground loop hum when routing
signals directly to other equipment or mixing consoles. However if ground loop hum is not
audible, you may get superior shielding from outside noise sources with the button in the GND
setting.
User Tip: When using the XLR Line out for recording direct-to-computer, we would
recommend you insert a suitable device between the amp and computer such as A.R.T.'s
TubeMP with USB for extra gain control and USB conversion.
13. Speaker Out
The amp's minimum load is 4 ohms overall therefore you can connect a total of one 4 ohm
speaker cabinet or two 8 ohm speaker cabinets in parallel (by daisy chaining from one
cabinet to the other).
Note: The 200 watt rated power output (@ 4 ohms) is measured with the amp's Gain and
tone controls adjusted for minimal distortion. When shopping for a single 4 ohm cabinet, look
for one with a program power rating of approximately 250 watts, this will provide some added
capacity for handling "crunch" distortion.
Cabinet Impedance (ohms):
Power @ min. impedance (watts):
Minimum Impedance (ohms):
Burst Power - 2 cycle:
Speaker Configuration - LF (Size / Power):
Input Channels:
Channel 1 - inputs:
Channel 1 - controls:
Channel 1 - switches:
Channel 2 - inputs:
Line Out (type / configuration):
Line Out Sensitivity (Vrms):
External speaker output / location:
Dimensions (DWH, inches):
Dimensions (DWH, cm):
Weight (lbs / kg):
1/4-inch T.R.S.
Phone Plug
Tip = 0°
Ring = 180°
Sleeve = Ground
Specifications
Model:
SB200H/SB106
Type:
SBH200H bass amp / SB106 bass amp & compact cabinet
SB200H: 4 ohms
SB106: 8 ohms (internal) 4 ohms (external)
200 watts
4 ohms
250 watts
SB106: 6.5 / 150W (internal)
2
passive 0 dB, active -6 dB
Gain, Bass, Low Mid, High Mid, Treble, Low Expander
Mute, Ground Lift, Line Out Pre/Post EQ
Aux In - 1/8-inch
Balanced Switchable Pre-EQ/Post-EQ, Ground Lift switch
1 Vrms
red,blue protect & standby, power
LED Indicators:
Protection:
clip,thermal, overcurrent.
Combi-Jack (1/4-inch/Speakon™) / rear of unit
Other Features:
1/4-inch head phone jack, Tuner out
7.5 x 8 x 1.75
SB106: 9 x 9.5 x 12.5
SB200H: 19.1 x 20.35 x 4.5
SB106: 22.9 x 24.2 x 11.5
SB200H: 2.375/1.1
SB106: 15/6.8
Balanced 1/4-inch T.R.S. to Balanced XLR
4
Specifications subject to change without notice
XLR Plug
(Male)
Pin 1 = Ground
1
2
Pin 2 = 0°
3
Pin 3 = 180°
Publicité
