Transport And Storage - Legend DRI-EAZ Velo Guide D'utilisation

required, have your equipment model, serial number and
original proof of purchase available and call your
distributor for assistance with obtaining a return material
authorization (RMA).
OPERATING INSTRUCTIONS
Note that the Velo can be placed in a variety of positions
for drying and air circulation. See Fig. B for details.
1. Unwrap the cord and plug the unit into a standard
115V GFCI-protected outlet. CAUTION: Be sure
switch is in the off position before connecting unit to
power outlet.
2. Direct the Velo outlet toward the surface to be dried.
TIP: On the Velo Pro, the airflow may be adjusted by
pressing the Up or Down arrow on the speed control (Fig.
D). A digital readout shows the approximate amp draw.
Use this value to maximize the number of Velos you can
place on a single circuit.
3. When surface is dry to the touch, switch the unit off
and reposition the unit in the next area to be dried.
4. When finished, unplug the unit and re-wrap the cord in
the cord wrap.
For additional instructions about the use of airmovers for
restorative drying, see Tech Tips under Resources on
www.LegendBrandsRestoration.com.
Electrical safety devices
Circuit breaker: If the circuit breaker detects overload or
short circuit conditions, the breaker will automatically shut
off the electrical supply. If this occurs, check the power
cable carefully for any damage and ensure it is plugged
into a properly grounded outlet. Press the Circuit Breaker
Reset Switch (Fig. A) to reestablish the electrical supply.
Ground Fault Circuit Interrupter: If the GFCI device
detects a ground fault, it will automatically shut off the
electrical supply. If this should occur, check the power
cable carefully for damage and ensure it is plugged into a
properly grounded outlet. Press the GFCI reset button
(Fig. A) to reestablish the electrical supply.

TRANSPORT AND STORAGE

Always use the handle to load or carry the unit.
Wrap cord in either direction under front Cord Wrap tab
and rear bottom edge (Fig. A). Pull cord snug and secure
with plug clip.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully
to prevent sliding and damage to the unit and/or injury to
vehicle occupants.
Keep unit dry. Do not expose the unit to rain or snow.
MAINTENANCE
WARNING: Unplug unit before performing any
maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use.
Always grasp the plug (not the cord) to unplug.
As needed
The exterior may be cleaned with a mild solution of
detergent. Ensure housing is completely dry before use.
To clean interior, see Fig. C for instructions.
109042H
Fig. C: Disassembly
To disassemble for cleaning:
1. Lay the unit on its top
(upside down). Remove the 4
blower bolts from the bottom
of the unit.
2. Turn the unit right side up
and remove the 14 screws
around the perimeter of the top
housing and electrical
enclosure.
3. Open the electrical box and
feed the blower cord back
through the opening to create
slack inside the housing.
4. Lift the top housing shell
and electrical enclosure
together and flip them over
next to the base to expose the
inside of the housing.
5. Lift the blower out for full
access to the inside of the
housing.
6. Reverse the steps for
reassembly. IMPORTANT: Be
sure to pull any slack blower
cord back into the electrical
enclosure before the lid is
placed on the electrical
enclosure.
Fig. D (Pro only)
Variable speed control with amp and total unit hours
display
FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or
the Legend Brands Service Department at
800-932-3030.
Be sure to visit warranty.legendbrandsrestoration.com
register your purchase. Your registration will help us
provide you with updated product information as needed.
WARNING: This product and other substances
that may become airborne from its use contain
chemicals, including lead, known to the State of California
to cause cancer, birth defects, or other reproductive harm.
For more information, go to P65Warnings.ca.gov
2
to
Legend Brands, Inc.