Cadac CITI CHEF 40 Mode D'emploi page 5

4. Fitting and Changing the Gas Cylinder
• After use, turn off the control knob to the off position ("•" - turn fully clockwise) and close the
gas cylinder valve.
• Ensure that the gas cylinder is fitted or changed in a well-ventilated location away from any source
of ignition, such as naked flames and away from other people.
• Do not smoke while changing the cylinder.
• When you need to replace your empty cylinder, make sure that the gas is closed at the cylinder
valve.
• Remove the regulator from the empty cylinder.
• Avoid twisting the hose whilst connecting the regulator to the new/replacement cylinder.
• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
• Place the full cylinder in its allocated space and attach the regulator connection to the cylinder.
• Ensure that a complete gas seal has been made (check for the smell of gas around the connection
joint). Do not check for leaks with a naked flame. Use warm soapy water only, applied to the
joints and connections of the appliance. Any leakage will show up as bubbles around the leakage
area. If you are in doubt, contact your nearest stockist.
5. Cleaning
• Allow the appliance to cool down before you clean it.
• Use a damp cloth wrung out in a solution of soapy water to clean the exterior and cylinder storage area.
• The grill plate is coated with a tough durable ceramic non-stick coating that has been used with great success on some of the best
cookware in the world. Never the less, taking care of it can help you to enjoy extra years of healthy, easy, non-stick cooking.
• Whilst the non-stick coating is very durable, it can easily be damaged by the use of metal cooking utensils. It is therefore
recommended that only plastic or wooden utensils be used when cooking.
• Always allow the grill plate to cool before immersing it in water.
• Make sure that no water gets onto the burners or pilot/light area. Wipe the appliance completely dry before use.
• Do not use abrasive cleaners as they may damage the surfaces.
• Clean the appliance after each use. After cleaning recondition the surface with a light wipe of oil.
• Do not use any high-pressure steam equipment or a water jet to clean the appliance.
• Remove the fat from the moat of the Fat Pan.
• Note: For stubborn stains, oven cleaner may be used.
6. Maintenance
• If you clean and maintain your appliance on a regular basis, the life of your appliance will extend and possibility of problems will
decrease.
In case of a spattering flame or jet blockage:
• Clean your burner ports in case of an over spill.
• CADAC recommends to clean or replace the jets every six (6) months to ensure continued efficient operation of your appliance.
• This may be done by removing the jet using standard tools and blow any dirt from the jet, alternatively, you may purchase new jets
from your local CADAC store. Do not attempt to clean the jet mechanically.
Service intervals and servicing:
• CADAC recommends the service of your appliance to be every twelve (12) months by a service agent to ensure continued efficient
operation.
• Note: Any technical work on the appliance should only be performed by a qualified technician.
• Check your gas hose and connections regularly for and signs of leaks and every time the gas cylinder is re-filled.
• Should the appliance operate abnormally after storage and all checks have not isolated the problem, the venturi may be blocked. A
blocked venturi would be indicated by a weaker yellowish flame or no flame at all in extreme cases. Under these circumstances it will
be necessary to remove the burner and to check and thoroughly clean out any foreign matter which may have gathered in the venturi.
7. Storage
• Always allow the unit to cool down before storing.
• Turn off the cylinder valve supplying gas to the appliance, if you remove the cylinder, then disconnect the cylinder.
• Store cylinder in a well-ventilated area away from combustible material. Storage of cylinders should preferably be outdoors and must
NOT be in a basement.
8. Returning the appliance for Repair, Service & Warranty
• Do not modify the appliance. This may cause the appliance to become unsafe. Any modifications will render the CADAC warranty null
and void.
• If you cannot rectify any fault by following these instructions, contact your local CADAC distributor for advise, inspection or repair
instructions.
• Please keep all proof of payments and the installation certificate for warranty purposes, if these cannot be supplied then all warranties
will be considered void.
• This CADAC appliance is guaranteed by CADAC for a period of 5 years against factory fault.
503-0676 LEV11 (5610) Citi Chef 40 - User Manual (EU & SA).indd 3
3 3
GB
Fig. 5
2018/10/03 09:09:16