Vivog EQ10102 Notice D'utilisation page 4

ASSEMBLY INTRUCTION
1- Put the tub basin (4)-A on the tube base (4)-B, bolt the inner hexagon
screw (7), washer (15), spring washer (9) and nut (16) to every pre-drilled
holes in the tub base (4)-B as per the attached picture.
2- Put the sponge gasket (12)-A into the drain (11), and then put it into
the hole of the tub basin (4)-A. Put the rubber gasket (12)-B into the drain
and use the plastic fix nut (13) to bolt the rubber gasket. Connect the
hose for the drainage (14) into the drain and bolt the screw in the hose.
3- Bolt the bottom of the back panel (2) to the tub basin (4)-A. Use an
inner hexagon screw (7), two Ø16mm washers (8), a spring washer (9)
and a nut (10) in every pre-drilled hole.
4- Bolt the bottom of the left-right panels (3) to the tub basin as per the
step 3. The panels are pre-shaped, so the smooth part of the panels
must be inside the bath and the tap must be on the right side of the bath
when you are facing it.
5- Bolt the grooming arm (1) to the left/right panels (3) as per the step 3.
6- Put the movable plate (5) into the tub basin (4)-A.
PARTS LIST FOR TAP
1. Bolts for soap holder (x 2)
2. Soap holder (x 1)
2b. hook for soap holder (x 2)
3. Shower (x 1)
4. Tap (x 1)
5. Bolts for shower holder (x 2)
6. Shower holder (x 1)
7. Right-side panel (x 1)
8. Washer (x 4)
9. Nuts for soap holder (x 2)
10. Water pipe connection (x 2)
11. Plastic nut for adjustment (x 2)
12. Nuts for shower holder (x 2)
13. Hose connection (x 1)
14. Left-side panel (x 1)
15. Hose for shower and tap (x 1)
16. Cold and hot water hose (x 2)
TOOLS NEEDED:
• Hex wrench
• Hex screwdriver
• Hex key
• Pliers
ASSEMBLY INSTRUCTIONS FOR TAP:
1- Let the water pipe connection (10) go through the right-side pannel (7).
Connect tap (4) into the left side of the pipe connection (10), connect the
plastic nut for adjustment (11) into the other side and then tighten them.
(make sure to not forget the two rubber joints)
2- Screw the cold-and-hot water hose (16) into the water pipe connection
(10) and tighten them.
3- Let the bold for shower holder (5) go through the shower holder (6). Fix
the washers (8) and nuts for show holder (12) on the right-side splash (7)
as the attached picture.
4- Let the bolts for soap holder (1) the two hooks and use the washer (8)
and the nuts (9) 2x2 to tighten them. Put the soap holder on the back
deflector according to your choice.
Optional : Connect the two ends of the hose for shower and tap (15)
into the shower (3) and tap (4) and then tighten them. Insert the
shower (3) into the shower holder (6).
Let the hose connection (13) go through the left-side splash (14) and then
tighten it. Adjust leveling feet on the stand to have the drain
approximately 1/8'' lower than the opposite side of the tub. This allows
water to drain better.
Please open the package be careful and check the spare parts are
complete, please contact our after sales services timely if you find some
parts missing or damaged.
GUARANTEE
the date of purchase, the guarantee terminates at this time even if the
bathtub has not been used. It is therefore advisable to keep the proof of
purchase (receipt and original packaging).
The guarantee is applicable for normal conditions of use and not
intensive, with regular maintenance of all parts.
The guarantee covers all mechanical manufacturing defects.
The replacement or repairs of parts that are subject to normal wear or
resulting from misuse are therefore excluded.
Any repairs made during the guarantee period do not result in a
prolongation of the latter.
The guarantee is not valid if the bathtub has been damaged as a result of
negligence, inexperience, or during transport.
The replacements or repairs covered by the guarantee are free of charge
by sending the bathtub directly, in its original packaging, with proof of
purchase to:
VIVOG SAS
2 Rue de la Briaudière - CS 40001
37515 BALLAN-MIRÉ CEDEX- FRANCE.
Tél. +33 (0)2 47 73 38 38 - fax. +33 (0)2 47 73 38 48
email : infos@vivog.fr - www.dogcat.com
Shipping costs are at the expense of the purchase.
PI10256