Télécharger Imprimer la page

Imiola HAK-POL I/006 Mode D'emploi page 5

Iveco daily vi model 35s

Publicité

Odkręcić zderzak.
Elementy E i F przykręcić do podłużnic śrubami M10x40 8.8 (pkt 3)
Elementy C i D przykręcić do podłużnic śrubami M12x40 8.8 (pkt 2) stosując nakładki E i F.
Przykręcić belkę haka A śrubami M12x35 8.8 (pkt 1)
Przykręcić zderzak.
Dokręcić wszystkie śruby z momentem wg tabeli.
Przykręcić kulę i blachę gniazda elektrycznego śrubami M16x45 8.8.
Podłączyć instalację elektryczną.
Unscrew the bumper.
Screw the elements E and F to the frame side members with bolts M10x40 8.8 (point 3)
Screw the elements C and D to the frame side members with bolts M12x40 8.8 (point 2) using plates E and F.
Screw the main bar A with bolts M12x35 8.8 (point 1).
Screw the bumper and lamps.
Tighten all the bolts according to the torque setting- see the table.
Screw the bumper.
Fix the ball and electric plate.
Connect the electric wires.
Dévissez le pare-chocs.
Fixez les éléments E et F aux longerons a l'aide des boulons M10x40 8.8 (point 3)
Fixez les éléments C et D aux longerons a l'aide des boulons M12x40 8.8 (point 2) en utilisant des superpositions E
et F.
Fixer la barre a crochet A avec les boulons M12x35 8.8 (point 1).
Vissez le pare-chocs.
Serrer tous les boulons avec un couple de serrage selon tableau.
Visser la boule et la tôle de la prise électrique avec les boulons M16x45 8.8.
Brancher l'installation électrique.
Die Stoßstange abschrauben.
Die Bauteile E und F an die Längsträger mit Schrauben M10x40 8.8 anschrauben (Punkt 3).
Die Bauteile C und D an die Längsträger mit Schrauben M12x40 8.8 (Punkt 2) mit den Pads E und F anschrauben.
Befestigen Sie die Hakenstange A mit Schrauben M12x35 8.8 (Punkt 1).
Die Stoßstange anschrauben.
Ziehen Sie alle Schrauben mit dem Drehmoment gemäß der Tabelle an.
Schrauben Sie die Kugel und den Steckdosenblech mit den Schrauben M16x45 8.8 an.
Die elektrische Installation anschließen.
Desenrosque, el parachoques.
Fijar los elementos E y F a los largueros con tornillos M10x40 8.8 (punto 3)
Fijar los elementos C y D a los largueros con tornillos M12x40 8.8 (punto 2) usando la superposición E y F.
Fije la barra de gancho A con tornillos M12x35 8.8 (punto 1).
Fijar el parachoques.
Apretar todos los tornillos con el par según la tabla anterior.
Apretar la bola y la placa de la toma de corriente tornillos M16x45 8.8.
Conectar la instalación eléctrica.

Publicité

loading