Segway Ninebot NEB1002-H1 Manuel Utilisateur page 2

1 Packing List
Battery Pack
Ambient Light
Power on the KickScooter. Press the Power Button to
turn on/off the ambient light.
* E22D, E25D, E45D does not have this feature.
Rail
Accessories
M4 Screw M3 Screw
Rubber Stopper
× 2 × 1
When unboxing your battery pack, please verify that the above items are included in the package. If any
components are missing, please contact your dealer/distributor or nearest service center.
2 Installing
1. Remove the cover (a), and remove the M3
screws (b) with 2.5 mm hex wrench . Then
remove other components (c).
(c) (b) (a)
3. Align the rail. Pre-tighten the screws in
order with 2.5 mm hex wrench and tighten.
1
3
2 Pre-tightening
state
User Manual
User Manual
3 mm 2.5 mm 2 mm
Hex Wrench Hex Wrench Hex Wrench
2. Remove the screw (d) with 2 mm hex
wrench. Then remove the three screws
(e) on the stem with 2.5 mm hex wrench.
(e)
(d)
4. Install the external battery on the rail.
Fixate the two M4 screws (with 3 mm
hex wrench) and the M3 screw (with 2.5
mm hex wrench). Block the screw holes
with the rubber stopper when installed.
M4 Screw
M3 Screw
3 Charging
Steps:
Open the charge
①
Charge port
port cover.
Do not connect the charger if the charge port or charge cable is wet. Do not charge or use
your battery if it is damaged or see trace of water.
Your KickScooter is fully charged when the LED on the charger changes from red (charging)
to green (trickle charge). Close the charge port cover when not charging.
4 Safety Instructions
1. Battery model NEB1002-H1 is only suitable for the Ninebot KickScooter ES, E22, E45
series models. Battery model NEB1002-U1 is only suitable for the Ninebot KickScooter
E25 series. Do not use other models or brands of scooters, otherwise there may be
safety risks.
2. Do not store or charge the battery at temperatures outside the stated limits (see
Specifications).
3. Do not touch battery contacts. Do not dismantle or puncture the casing. Keep the
battery contacts away from metal objects to prevent short circuit.
4. Risk of fire. Do not expose the battery to fire.
5. Do not charge or use your battery if it is damaged or see trace of water.
6. Do not puncture the battery. Do not attempt to disassemble the battery. No user
serviceable parts.
7. Completely draining the battery may cause permanent damage to the battery. Charge
the battery after each ride and avoid draining the battery completely. Please read the
user manual before charging the battery.
8. Do not discard or destroy the battery. Refer your local laws and regulations regarding
battery recycling and/or disposal.
5 Specifications
Name Ninebot KickScooter External Battery
Model NEB1002-H1
Color Black
36 V
Nominal Voltage
42 V
Max. Charging Voltage
Nominal Energy
184 Wh
Nominal Capacity
5100 mAh
Storage Temperature 32—104°F (0—40℃)
Battery Management Over-heating, short circuit, over-current,
System over-discharge and over-charge protection
ES Series: ES1, ES2, ES2L, ES4
Suitable for Ninebot
E22 Series: E22, E22D, E22E
KickScooter model
E45 Series: E45, E45D, E45E
Insert the Close the charge
② ③
charge plug. port cover when
finished.
NEB1002-U1
Gray
36 V
42 V
215 Wh
5960 mAh
E25 Series: E25, E25A,
E25D, E25E