Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Appearance
Frame
panel
rail
Tie down bracket opening
on appearance panel
Hitch Shown In Proper Position
Equipment Required: 6- 8" Ratchet Extension
Fastener Kit: 24847F
Wrenches: 17mm, 19mm
Appearance panel
shown off vehicle
1
Qty. (4)
Hex bolt M12 X 1.25 X 35 CL8.8
1.
Remove the tie-down hook on driver's side. Note: remove the bolts leaving the appearance panel in
place. Return tie-down hook and fasteners to vehicle owner.
2.
Lower exhaust system at the rubber isolator leaving the rubber isolator in place on the exhaust. Note:
Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal. Be
careful not to allow muffler to fall under its own weight.
3.
Remove (2) fasteners holding rear muffler hanger. Return fasteners to owner.
4.
Raise the driver's side of the hitch into position through the tie-down bracket opening. With the
passengers side on the ground rotate the hitch through the cut-out. Leave hitch supported (jack, blocks,
2
nd
person).
5.
Raise the passengers side of the hitch over the tail pipe, sandwiching bracket between the frame rail and
exhaust hanger bracket. Loosely install fasteners.
6.
Install remaining fasteners as shown.
7.
Tighten all fasteners to the required torque specification.
8.
Reinstall exhaust.
Tighten all M12 CL8.8 fasteners with torque wrench to 65 Lb.-Ft. (88 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Fascia
Drawbar Kit:
3598
Drawbar must be used in the
Rise position only.
Frame
rail
2
1
Tie down
bracket opening
Toyota Prius
Existing
weldnuts
Appearance panel not shown
installation view for clarity
2
Qty. (4)
Conical washer 1/2"
Sheet 1 of 3
Part Numbers:
24847, 60263,
77220, 24796
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location:
Note: Fasteners typical
both sides
24847N
10-26-09
Form F206 Rev A 5605
(U-Haul)
Exhaust
hanger
bracket
Rev. C
Publicité
Manuels Connexes pour Cequent Performance Products 24847
Sommaire des Matières pour Cequent Performance Products 24847
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24847N 10-26-09 Rev. C 2009 Cequent Performance Products Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. de l’état de New York concernant les spécifications en matière de sécurité des systèmes et dispositifs d’attelage. z 2009 Cequent Performance Products Feuillet 2 sur 3 24847N 10-26-09 Rév.
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 24847N 10-26-09 Rev. C 2009 Cequent Performance Products Form F206 Rev A 5605...