Juliana Veranda Instructions De Montage page 4

GB
May we congratulate you on your new greenhouse
Dear Customer! DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
in the instructions. Assemble one pack at a time. All corresponding to the order in the assembly
nuts, bolts and fittings are contained in a Box.
instruction. Erect one pack at a time. All nuts
Each pack is specified in separate lists of
and bolts and fittings are found in bag No. 0
components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside Seen from the outside
Seen from inside Seen from outside.
SOME SAFETY PRECAUTIONS
• Assembly must only be carried out in dry and
calm weather.
Precautions.
• Always wear work gloves when installing the
• Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
• Always use working gloves while glazing.
• Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
• Assistants and especially children must be
care.
• We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
• Any ladders that are used must be placed on a
remove it with care.
level surface.
• We recommend to use protective glasses
• It is essential to have an assistant available.
while fixing the spring wire clips.
• Place the ladder on a level support.
PAGE 12: TOOLS
• It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 13: FOUNDATIONS
The column marked indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
If you buy our original base, the anchor legs must
be cast in cement. These holes must be dug out to
separately. It ensures you a stable and easy to
below the frost line (800 mm). Place the assembled
build base.
base with anchor legs over the holes so the anchor
If you make your own base the measurements
legs fit into the holes; it takes about 75 litres of
indicated must be external measurements.
concrete to fill up the holes.
If you buy an original base you furthermore
Make sure the base is completely level and square.
need about 75 litres of concrete and 6/8
To square the base, make sure the two diagonal
plastic-/concrete pipes of about 800 mm which
measurements are identical.
are placed in a non-freezing depth for the
The width of the front and back gables must also be
identical.
fastening of the corner and middle anchors.
The base must be 100% level and square; the
ATTACHMENT TO THE BASE
latter is ensured by checking that the two
If you construct your own base, you must drill holes
diagonal measurements are equal.
(7mm) in the ground frame between all the vertical
profiles. The greenhouse must then be secured to
Tools
the base using screws (A).
The mounting of the greenhouse requires the
If you use an original base, the greenhouse must be
tools shown on page 12.
secured to each vertical bar as shown on drawings
B/C.
Page 14-27:
PAGE 14-27: ORDER OF ASSEMBLY
Place the components as shown on the
Place the components as shown on the illustration
illustration and assemble in the order shown
and assemble in the order shown in the pictures. Do
in the pictures. Do not tighten the nuts
not tighten the nuts fully until the entire sub-frame
completely until the front gable construction
has been assembled.
has been assembled.
PAGE 22-25: DOORS AND WINDOWS
For easier assembly, we recommend that you oil the
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same Page 13:
time as the profiles.
(Fastening to the base).
PAGES 28-29: FITTING OF GLASS/
When constructing your own base you have
POLYCARBONATE
to drill holes (7 mm) in the ground frame
Important before assembly!
between all the vertical frames, the greenhouse
Make sure that the gables and sides are level
is then fastened to the base with screws (A).
and square and that door(s) and window(s) are
Using an original base the greenhouse is
functioning perfectly.
fastened to each vertical bar as shown on
The best order of assembly for the glass or drawing B/C.
polycarbonate is as follows:
Windows - Roof - Doors - Gables - Sides
Page 24-27:
For an easier assembly we recommend that you
PAGE 28-29: GLASS INSTALLATION
oil the screws for the doors.
Degrease the sheets and frames with spirit.
Start glazing, one pane at a time. Apply a 3mm
Fitting of glass/polycarbonate
silicone bead around the vertical frames as indicated
Important before glazing!
(the dotted lines on the illustration). (A 3mm bead of
silicone is sufficient to ensure maximum adhesion).
If you use more silicone than recommended, extra
Make sure that gables and sides are level and
tubes can be purchased.
square, and that door(s) and window(s) are
functioning perfectly.
If you accidentally break a pane, carefully pull the
broken glass outwards and loosen the silicone using
Best order of assembly:
a sharp craft knife.
1) Windows – 2) Roof – 3) Doors – 4) Gables
Clean the profile completely before inserting a new
– 5) Sides
pane of glass.
PAGE 28-29: POLYCARBONATE INSTALLATION
Page 30-33:
The illustrations at the bottom of pages 28-29 show
Glazing (illustration 1 to 8)
where to fit the polycarbonate sheets and strips. The
Degrease the sheets and frames with spirit.
type designation states the length in millimetres. If
Start glazing from below, one glass at a time.
adjustment is necessary, use a fine-tooth saw.
Apply a 3 mm silicone line on the vertical
NB! To avoid the growth of algae, prevent the
frames where indicated (dotted lines on
polycarbonate sheets from coming into contact with
the illustration). (A 3 mm line of silicone is
the ground by resting them on a sheet of cardboard.
sufficient to obtain maximum attachment). If
M-strips are fitted as shown on pages 28-29. Place
you do use more than recommended, you can
the upper part of the strip under the aluminium
buy extra tubes.
profile along the full length of the sheet and then
click the strip into position from above.
Spring wire clips and glassholders are to be
fitted as shown.
U-strips are fitted as shown on pages 28-29.
X = Spring wire clips, > = Glassholders
Fit the strip to the sheet and adjust the length.
In case of broken glass carefully pull it
If desired, the sheets may be sealed against insects.
Seal the top using aluminium tape or silicone. The
outwards and loosen the silicone by means of a
bottom should only be sealed with air-strip tape to
sharp craft knife.
allow condensation to escape (available from your
Clean the profile completely before inserting a
local dealer).
new pane of glass.
Your greenhouse is now fully assembled. However,
Page 34-37:
please note the following:
Mounting of polycarbonate
The illustrations at the bottom of page 34/36 MAINTENANCE
• Grease the doors (hinges and locks).
show where to mount the polycarbonate plates
• Keep the gutters free from leaves, etc.
and lists. The type indication states the length
• Adjust the windows as necessary.
in mm. A possible adjustment is made by
• Replace any broken glass.
means of a fine-tooth saw.
• Clean the greenhouse with disinfectant before
NB! To avoid the formation of algae the
and after the growing season.
polycarbonate sheets must not come into
contact with the ground. Rest them on a piece
WINTER PROTECTION
If you anticipate snow during the winter, we of cardboard.
recommend the following winter precautions:
• Support the apex of the roof in the middle.
A-lists are mounted as shown on page 35/37.
• Remove any deep snow from the roof.
Put the sheet into the bottom list, bend the
• Take precautions to prevent snow falling from
sheet slightly outwards and put it in the top list.
a tree or roof, for example.
• Remove the cylinders for the automatic
M-lists are mounted as shown on page 35/37.
window openers, if fitted (optional extras).
Place the upper part of the list under the alu.
• Secure the door(s) and window(s) to prevent
profile in the whole length of the sheet and
wind damage to the greenhouse.
hereafter click on the list from above.
WATER AND CONDENSATION
Please note that your greenhouse is not like a
B
conservatory, for example, and that you should
Sealing of the polycarbonate sheets
therefore be aware that the greenhouse may leak
The sheets may be sealed against insects.
during or after precipitation and that condensation
Close the top end off with alu-tape or silicone.
will occur on the inside of the greenhouse. Good
The bottom only with airstrip tape to let
ventilation will help prevent condensation.
condensation out (available at your local
dealer).
INSURANCE
Please note that not all insurance companies cover
greenhouses automatically. Please contact your Now your greenhouse is completely assembled.
insurance company to ensure that your greenhouse
However, please notice the following:
is covered.
Maintenance
GUARANTEE
• Grease doors (hinges and lock).
Juliana greenhouses are covered by a 12-year
• Clean the gutter for leaves, etc.
guarantee, which covers the replacement or repair
• Adjustment of windows.
of faulty parts. The guarantee does not cover
• Replacement of broken glass.
polycarbonate, glass, transport, assembly, freight,
etc.
• Clean the house with disinfectant before
Juliana greenhouses are covered by a two-year
and after the growing season.
warranty on painted parts, where fitted. Note that
marks on the paint may occur due to suspension of
Winter Protection
the profiles.
In areas with occurrence of snow we
The guarantee will be void if the greenhouse is not
recommend the following winter protection:
assembled in accordance with these instructions.
• Support the roof ridge at the centre of the
house.
COMPLAINTS
All our greenhouses are built to the highest quality
• Remove greater snow loads from the roof.
standards. However, should you experience any
• Take precautions against snow falling
problems, please contact your dealer at once. When
down from for instance a tree or a roof.
describing the defect, please state the greenhouse
• Dismount the cylinders for the automatic
model, the component number and the quality
window openers, if any (optional extras).
control number.
• Secure door(s) and window(s) preventing
wind damage to the house.
Congratulations on your new greenhouse, which we
hope will bring you a lot of pleasure for many years
to come. Insurance
Please note that not all insurance companies
Yours sincerely,
cover glasshouses automatically. Please
contact your insurance company to ensure an
Juliana Drivhuse A/S
insurance coverage.
Guarantee
Juliana grants a guarantee of 12 years which
covers replacement of faulty parts. The
guarantee does not cover polycarbonate, glass,
transport, assembly, freight etc.
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
USA