Publicité
Les langues disponibles
Les langues disponibles
PROGRAMMING FLOWCHART
ADD
Change
User
Master
Code
0
0
Enter Memory
Enter (000)
Position from
(001 to 999)
Enter new code
Enter new
(1 to 8 digits)
Master code
OR/AND
(1 to 8 digits)
Present Card
If the user has
both
pin and card
then
for access he
must
enter PIN
and present the
Card.
New User will be
assigned to
Relay1
Note: Press B to exit the menu in
any stage of the programming
EXAMPLES:
ADD PIN Code:
Assign User Code "12345" at Memory Position "5" and Relay 2 that activates for 4 seconds, assuming Master Code = 000.
Press 000B + 0 + 005 + 12345 + A + 3 + 005 + 2 + A + 2 + 04 + A + B.
ADD Card:
Assign an User card at position "6" and Relay 1 that activates for 3 seconds, assuming Master Code = 000.
Press 000B + 0 + 006 + Present Card + A + B.
ADD PIN Code + Card:
Assign User Code "6789" AND Card at Memory Position "7" and Relay 1 that activates for 5 seconds, assuming Master Code = 000.
Press 000B + 0 + 007 + 6789 + Present Card + A + 3 + 007 + 1 + A + 1 + 05 + A + B.
Start
Enter "Master Code" OR "000"(if first time in use)
1 small beep + 1 long beep + Yellow LED is ON
Set
Set
Assign
Relay 1
Relay 2
Output
Timer
Timer
1
2
3
Press (from
Press (from
Enter Memory
01 to 99)
01 to 99)
Position from
for time in
for time in
(001 to 999)
seconds
seconds
If press 00
If press 00
toggle mode
toggle mode
Press(1) for
Default:
Default:
Relay 1
03 seconds
03 seconds
OR/AND
Press(2) for
Relay 2
OR/AND
Press(3) for
Relay3
OR/AND
Press(4) for
Relay 4
OR/AND
Press(5) for
Relay 5
OR/AND
Press(6) for
Relay 6
OR/AND
Press(7) for
Relay 7
OR/AND
Press(8) for
Relay 8
OR/AND
Press(9) for
Relay 9
OR/AND
Press(0) for
Relay 10
www.xprgroup.com
Validate by pressing (B)
NO
Validation
OK?
YES
Set
Slave
I/O board
Device
Timer
4
5
Press (from
Press(1) for I/O
01 to 99)
board (RB0408)
for time in
OR
seconds
Press(2) for
or press 00
RTT/DINRTT/
toggle mode
RU2
or none
Default:
Default:
03 seconds
RTT/DINRTT/
RU2
Press A to validate
Multiple small beeps
NO
Validation
OK?
Yellow LED blinks rapidly
YES
Two Beeps
END
Press B (Yellow LED is OFF)
Multiple small beeps
+
Yellow LED blinks rapidly
Buzzer
Select
Delete
Backlight
Card Type
Read Range
Users
6
7
Press(0) for
Press(0) for
Press
Buzzer OFF
NONE
999
OR
OR
Press(1) for
Press(1) for
Buzzer ON
EM
Press(2) for
OR
Backlight OFF
Press(2) for
OR
HID
Press(3) for
Backlight ON
Default: EM
OR
Press(4) for
backlight on
key
press
Press(5) for
dimmed
backlight
Press(6) for
reader's
read range
press(9) for
+1KHz
press(7) for
-1KHz
Default:
Buzzer ON
Default:
Dimmed
Backlight
+
Delete
All
Single
User
8
9
Memory
position from
(001 to 999)
7
Publicité
