Publicité
Les langues disponibles
Les langues disponibles
START UP
Open the battery compartment (underneath).
Insert four LR20 alkaline batteries in the compartment (not supplied).
Close the compartment and turn the switch ON.
The drum (inside the feeder) will turn and set itself in the starting
position.
You will then hear the recorded message three times over (if one has
been recorded) and the time "12:00" will flash slowly on the screen.
Now you can set the clock so that the distributer functions correctly.
Read the paragraph "setting the clock" below to set the time.
Press START to finish setting the clock.
Once complete, the time of the first meal will be displayed on the
screen. All of the figures will now flash to indicate that no meals
have been programmed.
The first number indicates the meal number.
rd
th
The 3
and 4
numbers indicate the time of the meals.
Notes:
The default information is as follows: Meal alarm: 0 days.
Meal frequency: 4, and volume of the meal and portion: 1.
The feeder will vibrate for around 15 seconds whilst the food is being
distributed, to ensure that it flows out of the reservoir correctly.
If you hear a beep and the feeder does not start up, then the detector
on the food reserve tray has been triggered. Check that the outlet for
the food is not blocked. Do not place or use the feeder in full sun, as
the tray detector will be activated the sun's rays.
OPERATION
1) Setting the time
1: Press CLOCK to display the time: the time and clock icon will be
recorded.
2: Press and hold SET until all of the numbers flash.
3: Press CLOCK to set the time.
4: Press TIMER to enter the minutes.
5: Press SET to confirm the hour:
The screen will display either 12 or 24 to indicate the mode.
6: Press CLOCK to switch between 12 or 24 hour mode.
7: Press START to complete the programming.
2) Programming the meal alarm
1: Press DAY to display the day of feeding
2: Press and hold SET until the 1
3: Press DAY to indicate the desired duration (in days).
To feed ad lib, enter 0 for the day of feeding.
4: Press START to complete the setting.
3) Programming the mealtimes and frequency
1: Press TIMER to display the mealtimes
2: Press and hold SET until the 3
the first meal will be displayed on the screen.
3: Press TIMER to record the desired mealtime.
4: Press SET to confirm your settings and move to the next mealtime.
5: Press START to confirm the setting or start over from step 4 if you
wish to enter other mealtimes.
The last meal number displayed corresponds to the number of meals
per day. The timer will then start automatically and the TIMER icon
will start up.
Notes:
If all 4 meals have been programmed, the process is complete and the
timer will start automatically. The time of the next meal will then be
displayed. If only 1 meal has been entered, the mealtime will not be
displayed even if you press TIMER.
The 4 mealtimes must be recorded in order (i.e. the earliest first)
otherwise one or more of the meals will not be distributed.
4) Setting the volume / size of the portion
1: Press VOL to display the portion size / volume.
2: Press and hold SET until the 2
3: Press VOL to save the desired volume.
st
nd
and 2
numbers flash.
rd
th
and 4
numbers flash. The time of
nd
number flashes.
4: Press START to conclude the recording and confirm the selected
volume.
Notes:
One meal volume corresponds to 1/2 a cup of food.
"0" represents 10 portions, i.e. the equivalent of 5 cups of food.
5) End of programming to start automatic food distribution
1: Press START to start the programme.
The next programmed meal will start up and the TIMER icon will
flash.
Notes:
When the timer icon and all of the numbers on the screen are present,
the programme is running.
Once the feeding programme has started, you can stop it by pressing
both the SET and START buttons at the same time.
6) To feed your animal manually
Press the SET and VOL buttons at the same time.
One volume of food will be served. The recorded programme and the
quantity remain unchanged.
7) Preview the programs
1: Press TIMER to view the mealtimes. Only the numbers of the
recorded meals will be displayed. The first number indicates the meal
rd
th
number. The 3
and 4
numbers indicate the time of the meals.
2: Press VOL once to view the remaining number of portions and
days.
3: Press DAY to view the remaining number of days of meals.
4: Press CLOCK to view the time, the "clock" icon will be displayed.
If you do not press any keys for 8 seconds, the screen will display the
next mealtime and the TIMER icon will flash.
Notes:
By pressing TIMER to scroll through the entered mealtimes, you will
only be shown the number of meals that you have recorded.
Only the first mealtime will be shown if you have only entered one
meal.
If the timer icon flashes, it means that the mealtime is near, whilst if it
is not flashing then the mealtime has just passed.
The volume and day are displayed on the same screen: The 1
figures correspond to the remaining days of meals and the 3
corresponds to the size of the portion.
8) Food alarm
Your automatic feeder has an alarm (continuous beep) to warn you
when the program has come to an end and that the food will no longer
be distributed.
The alarm sounds at 6h00 the next day to avoid disturbing you during
the night.
To stop the alarm: press any key.
To restart the program that you have recorded, simply press START.
9) General notes
The time is displayed in either 12 hour or 24 hour mode.
The "PM" icon indicates operation in the 12-hour mode.
The days of feeding can be changed at any time, but the previous
program will be replaced and the program will start again from day 1.
The time and volume of the meal can be changed at any time and the
new program will be memorised for the remaining days of the
program.
Once the program has started, the days recorded will be deducted
every day at midnight until the end of the program. Then, it will return
to the original number of days that you have recorded.
If the TIMER icon does not appear and all the figures are flashing,
then no program has been recorded.
However, if the TIMER icon appears and all of the figures are
displayed on the screen, the program has started.
When the CLOCK icon appears, the time is recorded.
When a red light flashes, the battery is low and should be replaced.
st
nd
and 2
rd
figure
Publicité
