Publicité
Les langues disponibles
Les langues disponibles
2 Channel receiver with self-learning,
GB
it manages standard codes from 12 till 64 and rolling
it manages standard codes from 12 till 64 and rolling HCS©
► RECEIVER CONNECTION
POWER SUPPLY (2 and 3). The receiver can be powered with
12 or 24 Vac/dc. If yu use direct current respect the polarity. (The
positive in the terminal no. 3).
ANTENNA (1 and 2). The antenna should be connected with
positive side in the terminal no.1 and the negative in the terminal
no. 2.
If you use only one cable (17 cm for freq. 433.92 Mhz - 8,5 cm
for freq. 868 Mhz), this has to be connected to the terminal no. 1.
EXIT. The exit of the relay's contact ( normally opened) is on the
terminal 4 and 5 .
Please don't connect the cable s to high tension and make
sure that the current is not more than 1 ampère
► USING OF THE RECEIVER
*** IT IS NECESSARY TO EXECUTE THE MEMORY´S RESET
***
ATTENTION!! this operation cancel all the codes in the memory.
It is necessary to cancel the memory before to learn the fi rst trans-
mitter, how to cancel:
1.
Make sure that the exit has not been activated (the contact
of the relay is open).
2.
Make sure that the receiver is not learning. The red led
must be switched off or it is fl ashing shortly
3.
Keep the button till the red led is lighting.
4.
Wait till the red led is switched off or it is fl ashing.
CODE MANAGING
This receiver can manage standard codes from 12 till 64 bit and
rolling codes HCS©. The fi rst learned transmitter establish the
code's type taht the receiver has to manage, it means that the
transmitter has to have the same code's type. Concerning the roll-
ing codes it is possible to activate or disactivate the key'scontrol
and the rolling counter. With this function you can choose the se-
curity level of the receiver.
+ ANTENNA
- ANTENNA
+ POWER SUPPLY
RELAY EXIT
BUTTON
1
-
2
+
3
4
5
► ACTIVATION OR REMOVE
ROLLING CODE'S CONTROL
This operation is necessary to activate or remove the key's control
and the rolling code counter. If you active this control , the receiver
will accept ONLY the rolling code with owner key (producer key)
and will control the rolling counter, in a way that the tranmitter
cannot be copied.
The operation is as follow:
1.
Make sure that the receiver 's exit are removed and are
not in self-learning
2.
Press and eave the button.The red led is lighting.
3.
Press and leave the button.The red led is fl ashing and
lighting .
4.
Press and leave the button. The red led is switched off and
remains switched off if you need the fuction is removed and
light shortly if the funciton is activated.
TRANSMITTER'S LEARNING
To learn a code make as follow:
1.
Make sure that the receiver 's exit is not active.
2.
Push and leave the button The red led is lighting
3.
Push the transmtter's button within 5 sec.If the code has
been learnt the red led is fl ashing shortly. If the red led
is fl ashing slowly it means that the memory is full. If the
red led is not fl ashing it means that the transmitter is not
compatible
STEP-BY-STEP FUNCTION
The receiver 's exit can be set up for step-by-steep function (to
be active or to be removed). If you want to active or remove this
function you have to press the button when the exit is active If the
exit are in the NORMAL FUNCTION, it will be operating the func-
tion step-by-step, but if it was already active, the exit will working
with a normal process.
TRANSMITTER'S CANCELLATION
This operation can cancel one single transmitter.
1.
Press and leave the button. The red led is lighting .
2.
Press the transmitter's button. If it is already on the mem-
ory, the red led is fl ashing for 3 sec. and then return to
the normal status. During this time press the button again.
LED
Publicité
