Renkforce 1590183 Mode D'emploi page 6

LED functions
The LEDs have the following functions:
• Blue LED
- The LED will light up when power is supplied
- The LED will flash during read/write access
- after switching on the docking station, the blue LED will flash until the HDD/SSD is ready
for operation
• Green LED
- The LED will light up briefly when the buttons are used
- The LED will flash 3x when confirming a password entry
- The LED will shine continuously once a password has been entered correctly and data is
accessible
- The LED goes out if data is not accessible
• Orange LED
- Setting/changing a password
• Red LED
- The LED goes out if data is accessible
- The LED flashes if an incorrect password is entered
- The LED goes out if a password has been entered correctly and data is accessible
Tips & notes
a) General information
• In the event of a defect in the docking station, the data on the HDD/SSD can only be ac-
cessed using a new docking station of the same type. Simply enter the password associated
with the HDD/SSD as usual to access the data.
• If you forget the password, access to the hard drive/SSD data will no longer be possible.
Therefore, store the password in a secure location.
• If it is attempted to install the password-protected HDD/SSD is directly into a computer or to
operate it via a conventional docking station or a USB HDD enclosure, the data will not be
accessible.
• Each HDD/SSD can be allocated a different password. In this case, make sure that you note
the allocated password of the HDD/SSD.
• The password can have 1 - 12 digits. The more places the password has, the harder it is to
crack the password.
b) USB
• USB 3.0 devices are downwards compatible. This also means that these operate on con-
ventional USB 2.0/1.1 ports - but in this case, only in the respective maximum USB speed.
• If you want to connect the docking station via a USB hub, the latter must also support the
USB 3.0 transfer mode, in order to reach the maximum speed.
• USB devices can be connected and disconnected during operation.
However, you should take into account that data may be corrupted or the operating
system may crash if the connection cable is disconnected while data is being trans-
ferred or while files are opened by a program.
In Windows, a symbol is displayed in the menu bar when the HDD drive (or other
USB devices) is (are) connected and in use; click this symbol to "separate" the
device, i.e. to terminate data transmission, so you can disconnect the connection
cable without risking a data loss.
• If you have upgraded your computer to be able to use a USB 3.0 plug-in card (e.g., if your
motherboard/computer is still not equipped with a USB 3.0 port), you must check whether the
plug-in card has its own power connection.
If such a power connection is available, the PC power supply has to be connected to
it; otherwise, the USB 3.0 port may not function properly or may not supply enough
power. Observe the operating instructions of the USB. 3.0 plug-in card.
Care and cleaning
Before cleaning the product, switch it off and unplug the wall plug transformer from the mains
socket.
Then, wait at least 30 seconds until the magnetic disks of the HDD drive have fully
stopped; otherwise, it may result in damage to the HDD drive and data loss.
Naturally, this is not required when using an SSD, since an SSD does not contain
any moving parts.
Never use abrasive cleaning agents, rubbing alcohol or other chemical solutions, since these
could damage the casing or even impair operation.
Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable materials and do not belong in the household was-
te. Dispose of an unserviceable device in accordance with the relevant statutory
regulations.
Technical data
a) Docking station
Port ............................................... USB 3.0 (compatible with USB 2.0/1.1)
Suitable drive ................................ 8.9 cm/3.5" or 6.35 cm/2.5", SATA
Supported capacity ...................... 10 TB
Encryption ..................................... AES-256
Password adjustable .................... 1 - 12 digits
Ambient conditions ....................... Temperature +5 °C to +40 °C, air humidity 5% to 90%
relative, noncondensing
Dimensions ................................... 142 x 103 x 82.5 mm (L x W x H)
Weight .......................................... approx. 301 g
b) Plug-in power adapter
Operating voltage ......................... 100 - 240 V/AC, 50/60 Hz
Output ........................................... 12 V/DC, 2 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2017 by Conrad Electronic SE. 1590183_V1_1217_02_VTP_m_en