Domintell Dmax Dimmax 420BLE Mode D'emploi

Dimmax 420BLE – User manual
Foreword
•
The Dimmax 420BLE universal dimmer can dim your LED lightings,
classical and halogens light bulbs (230V/12V via transformer).
• For an optimal functioning, only connect a single type of lamp to the
dimmer.
• In order to configure the dimmer, an external connected pushbutton
is required.
• The dimmer must have its own power supply (phase, neutral)
• The dimmer remembers the last dimming position (ex-factory the
dimming is set to 50%).
The Dimmax 420BLE power can reach up to 200W for LEDs and
420W for other lamps; 30 lamps max.
Wiring and configuration of the dimmer
In order to get a good dimming, these steps must be carefully followed:
Plug the dimmer according to
1.
the hereby enclosed diagram
(cut off the 230V with the
circuit breaker first).
The different modes of the
2.
dimmer can be selected with
the Dmax application available
for free on Google Play or
Apple App Store.
reconnecting the 230V power,
do a scan and then follow the
authentication process
order to add
corresponding Dimmax. Go to
settings to change the mode
and the dimming options. For
further details about the app,
see the instructions for use at
www.dmaxbydomintell.com
Plug the lamp and make sure
3.
it is properly dimming (ex-
factory configuration of the
dimmer is set to mode 1):
•
The lamp is correctly
dimming? (progressively and
to a minimum level)  Go to
step 4.
•
The lamp isn't correctly dimming? (improperly or not at all) 
Try with another mode.
•
The lamp isn't correctly dimming in any mode (improperly or
not at all)  Read thoroughly the tutorial available on the website.
Now set the minimal dimming level via the app (minimal threshold).
4.
In case you have a question, see the detailed version at
www.dmaxbydomintell.com
Technical data
Item number Type
5425014390261 420BLE Dimmer
EN_20180709
After
in
the
or contact your supplier.
Voltage Power
230V 0-420W (LED 0-200W)
•
Nominal conditions: 230V AC +/- 15%, 50 Hz, Ambient
temperature: -10°C to 40°C.
•
The Dimmax 420BLE is designed for lightings. Other loads
(such as engines) are forbidden.
•
Maximum wiring section per contact = 2,5 mm².
•
Maximum tightening torque: 0,4 N.m (use a dynamometric
screwdriver).
•
2 self-resettable
temporary overheating
•
2 additional physical protections: a thermostatic 230V power
cut-off switch, self-resettable, and a fuse (non-replaceable)
•
IP20 protection level.
•
Without halogen, RoHS.
•
Storage conditions: Temperature: -25°C / +70°C, Relative
humidity: < 75%.
•
For a safe installation, the device can only be mounted by a
qualified electrician.
•
The device must not be opened in any case (cancels warranty).
•
The device can only be installed inside, in a dry place,
compatible with IP20 devices.
•
During the mouting and unmounting of the device, cut off the
230V circuit-breaker.
•
The screws of the connectors of the device are unscrewed at
delivery and must be properly screwed before use.
•
After installation, the screws of the connector must be
protected so that could not be accessible for the final user.
After reconnexion of the 230V, the 420BLE Dimmax turns on. The
operation mode is set through the app:
Mode 1 = trailing edge dimming, to be used with:
- Classical 230V lamps (light bulbs or halogens (BEST mode for
a cold start), power 0 – 420W.
- Electronical converters or trailing edge compatible 230V
dimmable LEDs, power 0 – up to 200VA.
Mode 2 = leading edge dimming, also called "triac mode", to be
used with:
- Disc-wound transformers for 12V halogens (the Dimmax
420BLE automatically detects them and forces mode 2), power 0 –
380VA.
- Electronical converters or dimmable leading edge compatible
LEDs, power 0 – up to 200VA.
As soon as the mode is changed, the Dimmax 420BLE is ready
to work under the control of the pushbutton.
For a LONG PUSH (>0,4s) on the button: the dimmer turns on (if it
was OFF) and the dimming level slowly increases/decreases
between Min (settable) and Max (100 % = total conduction) level;
the last lelvel is maintained by releasing the button.
For a SHORT PUSH (<0,4s) on the button: the dimmer turns on or
off with a smooth transition.
Dimension
48 x 46 x 18
The Dimmax 420BLE complies with the following directives and
standards:
Directives
RED-directive : 2014/53/UE
EG-directive: 2014/30/UE
LV-directive: 2014/35/UE
Norm
EN 60669-2-1: 2004 + A1: 2009 +A12: 2010
Dimmax 420BLE
is manufactured in Belgium by:
Domintell S.A.
dmaxbydomintell.com
protections: against
Safety and environment
Operation mode settings
Pushbutton control
Directives and norms
overcurrent and