Campbell Hausfeld MP516803 Instructions D'utilisation Et Manuel De Pièces

See Warranty on page 4 for important information about commercial use of this product.
Operating Instructions & Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Mini Filter • Pressure Regulator
Description
The Campbell Hausfeld filter/regulator
combines a general purpose filter with
a pressure regulator in one compact
unit. The filter is designed to remove
most liquid and solid particles from the
air supply. The self-relieving pressure
regulator is used to adjust the outlet
pressure between 0 - 125 psi.
Specifications
Max. Temperature . . . . .125º F (52º C)
Max. Input Pressure . . . .150 psi
Max. output Pressure . . .125 psi
Air Inlet/outlet . . . . . . . .1/4" NPT
Filter Element . . . . . . . . .5 micron
Unpacking
After unpacking the unit, inspect
carefully for any damage that may have
occurred during transit. Make sure to
tighten fittings, bolts, etc., before
putting unit into service.
Safety Guidelines
This manual contains information that
is very important to know and under-
stand. This information is provided for
SAFETY and to PREVENT EQUIPMENT
PROBLEMS. To help recognize this
information, observe the following
symbols.
an imminently hazardous situation
which, if not avoided, will result in
death or serious injury.
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
a potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
important information, that if not
followed, may cause damage to
equipment.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2007
General Safety
Information
This product is a part of a high pressure
system and the following safety
precautions must be followed at all
times along with any other existing
safety rules.
Read this instruction manual
before installing this device
to the air supply system. Be
thoroughly familiar with
the controls and the proper
use of the equipment.
Safety glasses must be worn
during operation.
1. Always work in a well ventilated
area.
2. Do not exceed any pressure rating
of any component in the system.
3. Protect air lines from damage
and/or punctures.
4. Check air hoses for weak or worn
condition before each use. Make
sure all connections are secure.
5. Keep all nuts, bolts and screws tight
and ensure equipment is in safe
working condition.
Danger
indicates
This product is specifically
designed for compressed air
service ONLY. Use with any
other material (liquid or gas) is a
misapplication and not permitted. Use
Warning
or injection of certain hazardous
indicates
liquids or gases in the system (such as
oxygen, alcohol or liquid petroleum
gas) will harm the unit and result in a
combustible condition or hazardous
external leakage. Misapplication will
Caution
void all warranties and manufacturer's
indicates
responsibilities.
flow capacity of regulators is limited.
Notice
Install additional pressure relief
indicates
devices to alleviate over pressurized
conditions. Written approval must be
obtained from manufacturer if this
For parts, product & service information
visit www.chpower.com
Model MP516803
MANUAL
Figure 1
device is to be used for life support
systems or other non-industrial
applications.
Installation
Disconnect power and
release all pressure from the
system before attempting to
install, service, relocate or perform any
maintenance.
1. Locate the air flow inlet (See Figure
2, detail). Air must flow in the
specified direction for this unit to
function properly.
Air
flow
inlet
Figure 2
The
2. Install the gauge. Use PTFE tape on
relief
all threads.
6
4
8
2
10
0 11
BAR
100xkPa
psi
IN
IN281501AV 3/07