habitat et jardin 91 cm Notice De Montage Et Informations À Lire Et À Conserver page 15

1. To prepare the Ladder Handle Assembly (see Fig. 1), the Machine Screws should be installed from the
inside of the Ladder Hinge and then through the Ladder Handle
with the safety label on the outside. Make sure that the English warning label is facing out on both handle
sections. Install the Lock Washer, and thread the Cap Nut on until the Ladder brace tightens up against the
Handle
2. The Machine Screws
Ladder Handle. Install the Flat Washer, , Lock Washer, and thread the Cap Nut on until the Ladder Brace
tightens up against the Ladder Handle. (See Fig. 1)
3. To prepare the Ladder Leg Assembly (see Fig. 2), start with one "R" ladder leg section. Carefully pre open
one Ladder Step Clip from the side, just enough to get over the top section of the Ladder Leg, and slide it
from the top of the leg down to the lowest indented section as shown in the Figure 2. The ridge on the
Ladder Step Clip should be on the inside of the leg as shown in the Figure 2. Repeat the same process to
make the left "L" ladder leg section
4. Slide a Ladder Step down over both legs. Make sure that the side of the stop marked with an "R" is on
the right side leg. Slide the stop down until the ladder step clips inserts into the underside of the stop and
the ridges inside of the clips lock into place. The ladder step clips should stay in the indented section of
the ladder leg as you press the steps down over them. The ladder step clips should insert flush against the
bottom of the step. (See Fig. 3).
5. To prepare the Swivel Ladder Leg Assemby (see Fig. 4), start with one Straight Ladder Leg. Carefully pre
open one Ladder Step Clip from the side, just enough to get over the top section of the Straight Ladder Leg,
and slide it from the top of the leg down to the lowest indented section as shown in the Figure 4. The ridge
on the ladder clip should be on the inside of the leg as shown in the Figure 4. Repeat the same process to
make another Straight Ladder Leg section.
6. Slide a Ladder Step down over both Straight Ladder Legs. Slide the step down until the Ladder Step Clips
insert into the underside of the stop and the ridges inside of the clips lock into place. The Ladder Step Clips
should stay in the indented section of the Ladder Leg as you press the steps down over them. The Ladder
Step Clips should insert flush against the bottom of the step as shown in the Figure 5.
7. Place the Swivel Ladder Clamp with Button at the topmost step of the Straight Ladder Leg as shown in
the Figure 4. The button should be installed facing outwards and the lock should be pointing to the front.
The Swivel Ladder Clamp is installed on the other side of the Straight Ladder Leg as shown in the Figure 4.
The small clamp should be pointing to the front.
8. The Machine Screws should be installed from the inside of the Straight Ladder Leg
on until the Swivel Ladder Clamp tightens up against the Straight Ladder Leg. (See Fig. 5).
9. Place the Ladder Bottom Clips at the bottom of the Straight Ladder Leg as shown in the Figure 4. The
Machine Screws should be installed from the Inside of the straight ladder leg. Thread the cap nut on until
the ladder bottom clips tighten up against the straight ladder leg (see Fig. 4).
10. Stand the Ladder Leg Assembly in the upright position, with feet facing outward, as shown in the
Figure 6. Place the ladder handles, with the Ladder Braces on the outside of the ladder, on top of both
ladder leg sections.
11. Make sure all of the steps are now level (parallel to the ground.) If one section is different, lift the handles
and turn the ladder leg section around. Re-install handles and push down tightly.
12. From the inside of the Ladder Handle, insert the two Machine Screws through the Flat Washers, then
through the Ladder Handle and fasten in place using the two Lock Washers and Cap Nuts . (See Fig. 6).
13. Stand the Left and Right Plain Ladder Leg in the upright position, with feet facing outward, as shown in
the Figure 6.
S E T U P I N S T R U C T I O N S
6
should be installed from the inside of the Ladder Handle
2
, and out through the Ladder Brace
- 2 -
- 15 -
2
, and out through the
13 . Thread the Cap Nut