Publicité
Les langues disponibles
Les langues disponibles
Operation
Keep long hair, ties, scarves, loose clothing, long necklaces or bracelets away from the input
slot.
Do not shred labels or items with labels affixed to them. Adhesive residue will attach to cutting
blades causing the shredder to malfunction.
Do not touch the blades of the cutting unit!
Observe the 2 min On / 30 min Off operating interval.
a) Setting up
1. Place the product on an even horizontal surface.
2. Place the cutting unit onto the collection container. The shredder will not operate if the collector does not
make complete contact with the safety interlock switch on the shredder.
3. Prepare material for shredding by removing labels, paper clips, staples, or any other foreign objects.
b) Shredding
1. Check that the switch is in the Off position.
2. Connect the shredder to the power supply.
3. Observe the shred capacity per pass:
- Paper: max 10 sheets (80 g/m
).
2
- CD / DVD / credit card: max. 1 pc.
4. Slide the selector switch to the correct position:
- On/Auto position: Paper.
- Rev /On CD position: CD / DVD / credit card.
5. Insert the item to be shredded into the correct slot:
- Paper: Large slot.
- CD / DVD / credit card: Small slot
6. Switch the power Off when finished shredding.
7. Disconnect the shredder from the power supply.
8. Empty the container.
c) Clearing paper jams
Always disconnect the shredder from the power supply before attempting to manually
remove blocked paper.
Never use objects of any kind to clear jammed CDs, credit cards, or paper.
Overloading the shredder, damp paper or improper alignment can cause the shredder to jam, if this happens:
1. Set the switch to Rev to back the paper out of the unit.
2. If paper will not clear using this method:
- Switch the power Off.
- Disconnect the shredder from the power supply.
- Manually remove any stuck paper by pulling it out.
d) Overheat protection
1. The Overheat warning LED will turn on if the shredder overheats. If this happens the power will be cut
off to allow the shredder to cool down.
2. Switch the power Off and let it cool for approximately 30 minutes, then try the shredder again.
Troubleshooting
Error
Cause
Plug not properly connected
to power supply.
Overheat protection has
been triggered.
Shredding does
The paper input slot jammed.
not start or
switches off dur-
ing shredding.
The collector is not making
contact with the safety inter-
lock switch on the shredder.
Shredding does
not stop after
The mechanical sensor may
the paper has
be jammed by paper.
passed through.
Too much paper has been
inserted.
Paper may be too thick.
Paper may be too thin, soft
Paper will not
or creased to reliably activate
shred.
the detection sensor.
Paper is inserted at an angle.
Solution
Check the connection.
See section "Operation → d) Overheat protection".
See section "Operation → c) Clearing paper jams".
•
Check that the shredder is aligned with the
notches on the collection container and sits
flush against it.
•
A full collector may cause the shredder to lift up
and break the interlock switch contact. Empty
the collector.
See section "Operation → c) Clearing paper jams".
Check that you have not exceeded max. number
of sheets.
Reduce the number of sheets being shredded.
1. Set the switch to Rev to back the paper out
of the unit.
2. Fold the paper.
3. Try again.
4. Set the switch to Rev to back the paper out
of the unit.
5. Line the paper up with the input slot.
6. Try again.
Maintenance, care and cleaning
Caution! The blades are sharp. Risk of injury.
Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the enclosure or cause the product to malfunction.
•
Before cleaning the product, switch it off and disconnect the mains socket from the mains outlet.
•
Do not immerse the product in water.
•
This product does not contain any components that require maintenance. Never attempt to open or
disassemble it.
•
Empty the collection containers regularly.
•
A dry, soft and clean cloth is sufficient for cleaning. Do not press too hard on the housing, as this can
lead to scratch marks.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste. At the end
of its service life, dispose of the product in accordance with applicable regulatory guidelines.
You thus fulfil your statutory obligations and contribute to environmental protection.
Technical data
Operating voltage/current ..................... 220 – 240 V/AC, 50 Hz, 1.4 A
Power consumption .............................. max. 260 W
Protection class .................................... II
Cutting slot width .................................. 222 mm (paper)
123 mm (CD / DVD / credit card)
Cut size ................................................. Paper: 4 x 38 mm (cross cut)
CD / DVD / credit card: 15 mm (strips)
Cutting speed ....................................... 2.2 m/min
Number of pages .................................. max. 10 sheets (80 g/m
Number of CD / DVD / credit card ........ max. 1
Container volume (paper) ..................... 18 L
Noise level ............................................ 70 dB
Interlock switch ..................................... yes
Intermittent operation ............................ 2 min On / 30 min Off
Overheat protection .............................. LED warning, auto shut-off (approx. 30 mins cooldown)
Noise level ............................................ ≤70 dB
Safety level ........................................... P-4 (DIN 66399)
Operating conditions ............................. 5 to 40ºC, 40 – 95 % RH (non-condensing)
Storage conditions ................................ -2 to +70 ºC, 40 – 95 % RH (non-condensing)
Cable length ......................................... approx. 1.5 m
Dimensions (L x W x H) ........................ 354 x 211 x 406 mm
Weight .................................................. 3745 g (shredder), 793 g (container )
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
)
2
*2252304_v1_0820_02_dh_m_en
Publicité
