Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
24 port patch panel CAT6A
Item no. 1713217
Intended use
The product is intended for cabling of rigid network lines in accordance with CAT6A standards.
This then makes the connection of conventional patch cables to the RJ45 sockets possible.
For safety purposes, you must not rebuild and/or modify this product. Using the product for
purposes other than those described above may damage the product. In addition, improper use
can cause hazards such as a short circuit or fire. Read the instructions carefully and store them
in a safe place. If you pass the product on to a third party, please hand over these operating
instructions as well.
This product complies with statutory, national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Patch panel
• 4x cage nuts
• 4x screws
• 4x plastic rings
• 24x cable ties
• Operating instructions
Up-to-date Operating Instructions
Download the up-to-date operating instructions at www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the
product.
Safety instructions
Read the operating instructions carefully and observe safety instructions. If
you do not follow the safety information and information on proper handling
in these operating instructions, we will assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a
dangerous toy for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Never expose the product to mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
• Consult a technician if you are not sure how to use or connect the product, or if
you have concerns about safety.
• Maintenance, modifications and repairs must be carried out by a technician or a
specialist repair centre.
• If you have any questions that are not answered in these operating instructions,
please contact our technical customer service or other professionals
Connection and installation
• Remove the cover. Rotate the two clamping knobs to the left or right, the cover can then be
raised to the rear and removed.
• Carefully cut into the cable sheath of the network cable at approx. 50 mm. Do not damage the
shielding and the inner conductor!
• Pull off the cable sheath.
• Pull the braided shielding backwards over the cable sheath and twist it. Remove the shielding
of the wire pairs.
• Loosen the metal bracket for the strain relief in the patch panel for the corresponding port,
where you want to connect the cable.
• For cabling use either the colour coding according to T568A or T568B (in Europe T568A is
usually used). Do not mix the two colour codes on your network, or otherwise the network
connections may not work.
Guide the shielding of the cable pairs of the CAT6A cable up to the insulation displacement
terminals.
Pin
1
2
3
4
5
6
7
8
• Connect the wires (starting from insulation displacement terminal 8) with a suitable LSA
punch down tool. Pay attention to the correct colour coding.
• Secure the network cable with the strain relief, so that the shielding braid is located under the
strain relief and contact is achieved.
Do not use force; do not pinch the cable too tightly.
• Finally, the network cable is to be fixed at the rear end of the patch panel with a cable tie. Do
as described above for other network cables.
• When all the cables are connected, replace the cover. Secure the cover with the two clamping
knobs.
• Install the patch panel into your 48.3 cm (19") network cabinet. Suitable installation material
is enclosed for this purpose.
• Attach the grounding cable of the patch panel to a grounding connection provided for this
purpose.
• Label the cables and network ports on the patch panel in a suitable manner, so that you can
inspect the connections and cable connections more easily in the event of faults.
Care and cleaning
• Never use aggressive detergents, rubbing alcohol or other chemical solutions as these can
damage the housing or impair the product function.
• Use a dry, lint-free cloth to clean the product.
Disposal
The product must not be disposed of with the household waste. At the end of its
service life, dispose of the product according to the relevant statutory regulations.
Technical data
Cable diameter ............................. 5.0 - 8.5 mm (outside)
Wire diameter ............................... AWG 22 - 24 (0.41 - 0.63 mm)
Standards ..................................... ISO / IEC 11801:2002 class EA
EIA/TIA 568-C Cat.6A
Connection service life ................. min. 750 mating cycles (RJ45)
min. 200 mating cycles (insulation displacement terminals)
Operating conditions ..................... 0 to +70 °C, max. 75 % RH
Storage conditions ........................ -40 to +85 °C, max. 75 % RH
Dimensions (W x H x D) ............... 483 x 22 x 114 mm
Weight .......................................... 1093 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
T568A
T568B
white/green
white/orange
green
orange
white/orange
white/green
blue
blue
white/blue
white/blue
orange
green
white/brown
white/brown
brown
brown
*1713217_v1_0918_02_IPL_m_en
Publicité
