Stack ST3513 Instructions D'installation page 3

Change Low Warn Colour
(Region A colour)
Warn Colour Set Mode:
With power off, press and hold the WARN button. Apply power to the gauge.
Release the WARN button. The pointer will be at the stop pin and the dial
illumination will be off. Press and release the WARN button to cycle between
hIGh warn colour set and LOW warn colour set modes. In High Warn colour
set mode, the pointer will move to full scale and the dial will illuminate with the
current High Warn colour. In Low Warn colour set mode, the pointer moves
Change high Warn Colour
(Region C colour)
Warn Colour Set Mode:
With power off, press and hold the WARN button. Apply power to the
gauge. Release the WARN button. The pointer will be at the stop pin and
the dial illumination will be off. Press and release the WARN button to cycle
between hIGh warn colour set and LOW warn colour set modes. In High
warn colour set mode, the pointer will move to full scale and the dial will
illuminate with the current High Warn colour. In Low Warn colour set mode,
Lighting Mode
(Region B Colour)
This gauge allows the dial lighting to operate in two modes, Full On or
Dimmable. Factory default is Full On.
Full On:
In this mode, the white lighting wire is ignored. The gauge dial
lighting is always on at full brightness. (unless you select NO colour when
setting the Backlight Colour). If using Full On mode, white wire hook-up is
not needed.
Dimmable:
In this mode, the white wire is used to set the intensity of the
dial lighting from full brightness down to off.
Gauge Reset
It may be desired to reset the gauge. This clears programmable settings to
a system default. With power off, hold in both buttons.
Apply power to the gauge, wait two seconds, and release both buttons. The
dial face will flicker white several times and return to normal operation. At
this point, the gauge has been reset.
Reset Settings:
High Warning Set Point: Max Value
Low Warning Set Point: Lowest Value
Pro Control Active States
The active region for Pro Control outputs are user configurable. For
example, consider a pressure gauge with a low warning set point at 20 PSI .
The gauge can be configured so the associated Pro Control output is active
when the pointer falls below the set point [less than 20 PSI] (active low) OR
when the pointer is beyond the set point [greater than 20 PSI] (active high).
Likewise, consider a pressure gauge with high warning set point at 95 PSI.
Again, the gauge can be configured so the associated Pro Control is active
when the pointer falls below the set point [less than 95 PSI] (active low)
OR when the pointer progresses beyond the set point [greater than 95 PSI]
(active high).
To change the active state:
With power off, press and hold the PeAK button. Apply power to the gauge.
Release the PeAK button. Press and release the WARN button. The
gauge is now in Active State Set Mode. The pointer will point straight up at
the value in the top center of the dial. Press and release the WARN button
to the minimum position and the dial will illuminate with the current Low Warn
colour.
To change Low Warn Colour:
When the Low Warn colour set mode has been selected (see above), press
and hOLD the WARN button to cycle through the available colours. Once
you have selected the desired colour, release the WARN button. Don't press
any buttons for about three seconds. The dial will flicker white several times
to indicate the desired setting has been saved and the gauge will return to
normal operation with your new Low Warn colour selection. Colour selections
are saved when power is off.
the pointer moves to the minimum position and the dial will illuminate with
the current Low Warn colour.
To change high Warn Colour:
When the High Warn colour set mode has been selected (see above), press
and hold the WARN button to cycle through the available colours. Once
you have selected the desired colour, release the WARN button. Don't
press any buttons for about three seconds. The dial will flicker white several
times to indicate the desired setting has been saved and the gauge will
return to normal operation with your new High Warn colour selection. Colour
selections are saved when power is off.
To change the Lighting Mode:
With power off, press and hold the PeAK button. Apply power to the gauge.
Release the PeAK button and the dial face will illuminate with either white
lighting or blue lighting. Press and release the PEAK button to toggle
between Full On (dial is illuminated white) and Dimmable (dial is illuminated
blue). Once you have selected the desired mode, don't press any buttons
for about three seconds. The dial will flicker white several times to indicate
the desired setting has been saved and the gauge will return to normal
operation with your new mode selection. Mode selections are saved when
power is off.
Peak: Lowest Value
High Warning Colour: Red
Low Warning Colour: Green
Backlighting Colour: White
Lighting Mode: Full On
High Warning Pro Control State: Active High
Low Warning Pro Control State: Active Low
High Over Warn Set Point: Max Value
Low Over Warn Set Point: Lowest Value
to toggle back and forth between the low and high warning point active
state modes. Doing so will cause the dial to change back and forth between
green and red. When setting the low warning active state the dial face will
be green. When setting the high warning active state the dial face will be
red.
Once the designated warning mode is selected (green or red) press and hold
the WARN button to toggle between active high and active low. As you hold
the button the pointer will continuously sweep from the left of center and to
the right of center pausing at each side. Left of center is active low and right
of center is active high. Release the WARN button when the pointer is in
the position of the desired active state. Once you have selected the desired
state, don't press any buttons for about three seconds. The dial will flicker
white several times to indicate the desired setting has been saved and the
gauge will return to normal operation with your new state selection. State
selections are saved when power is off
NOTe: The Pro Control Active State does not
.
affect the colour of each dial region.