Unpacking The Product - Joovy Room2 701 Serie Mode D'emploi

1 Unpacking the Product

• Remove everything from the box and identify the parts using Figure 1.1. (not to scale)
A: playard, B: mattress, C: travel bag, mattress sheet (not shown), and documents (not shown).
• Discard all packaging materials properly including plastic coverings.
• DO NOT allow children to play with any packaging materials.
2 Unpacking/Assembling the Playard
• Keep children away from playard while unpacking and assembling.
• Open the travel bag and remove the playard and mattress.
• Release each of the Velcro® straps and slide them through the plastic ring as shown
• Set the mattress aside and position the playard so it is resting on the feet and wheels.
• DO NOT push the center down yet.
• With the center of the playard up, pull upward on each side rail until it locks into position. You will hear the rails lock into place.
See Figure 2.1.
NOTE: There is ONE mechanism that locks BOTH pieces of tubing on EACH side rail. See Figure 2.2.
CAUTION: DO NOT squeeze the release button underneath the locking mechanism while you are pulling up on these rails. Doing so may
prevent the locking mechanism from fully latching.
• Make sure that the top rails have become rigid. If they haven't, pull up again until they are rigid. You may need to lift the center of the floor
higher.
• Once you have locked the side rails in the up position, go back and check each side rail again to be sure they are all locked into position.
• Hold one side of the playard up and push down the center of the floor. See Figure 2.3.
• Place the mattress inside the playard with the soft side up.
NOTE: If using the sheet see section 3.
• Locate the Velcro® straps near the corners of the mattress.
• Slide the straps through the corresponding slots in the floor of the playard and secure it to the underside of the playard making sure the
strap goes over the bar. See Figures 2.4 and 2.5. Repeat this step on the other three corners.
Be careful not to pinch your fingers on the top corners during assembly. ALWAYS ensure that all side rails are locked
into position before using this product. ALWAYS secure the mattress to the playard floor with the Velcro® straps.
3 Attaching/Removing the Mattress Sheet
NOTE: This product comes complete with a custom fit mattress sheet. To use the sheet with your playard, please follow the instructions
below.
Before attaching the mattress to the playard, fit the sheet over the mattress with all four corners pulled tight. Then, feed the Velcro® straps
through the slots in the sheet and then through the slots on the playard floor. Slide the straps through the slots in the floor of the playard and
secure them to the underside of the playard as detailed in Section 2 and shown in Figures 2.4 and 2.5.
To remove the mattress sheet, detach the Velcro® straps and feed the straps through the slots in the sheet. Then, pull the sheet off of the
mattress.
Prevent possible strangulation or entanglement. Never use playard sheet unless it fits securely on the playard
4 Folding/Packing the Playard
• To fold the playard, release the Velcro® straps on the corners of the mattress from the underside of the playard floor. See Figure 4.1.
• Lift the mattress from the playard and set it aside. If necessary, remove the mattress sheet.
• Pull upward on the webbing loop near the center of the playard floor. Be sure that the center is pulled up all the way. See Figure 4.2.
• With the center of the floor pulled up, locate the button on the center of one of the top rails.
NOTE: The button is sewn inside the fabric near the center of each top rail. See Figure 4.3.
• Pull upward on the top rail and squeeze the button. Then push down until the locking mechanism is released on BOTH sides of the top
rail. See Figure 4.4.
NOTE: If the rail tubes do not unlock, do not force them. Lift the center of the floor higher and try again.
• Once you have successfully released BOTH tubes and folded that top rail, repeat this procedure on the other top rails until all four top rails
have been folded.
!
Adult assembly is required for this product. No Tools Required.
!
NEVER use items not recommended by Joovy with this product.
!
WARNING
WARNING
WARNING
mattress.
EN FR ES