Cequent Performance Products 75278 Instructions D'installation

Hitch Shown In Proper Position
Equipment Required: ½" Pull wire (Provided)
Fastener Kit: 75278F
Wrenches: 10mm, 15mm, 3/4, 7/8
Drill Bits: 1/2"
Exhaust hanger bracket installed through slot in passenger
side bracket Buick & all wheel drive models only
(4) Spacer blocks (2) per bolt location
see figure 3 for orientation
Hitch side bracket
Figure 2
Exhaust hanger bracket
installed through slot in
passenger side bracket Buick
& all wheel drive models only
Hitch side bracket passenger side
Middle 2 holes in
hitch side bracket
6
Figure 3
Orientation of spacer blocks
Buick & all wheel drive
models only
1
Qty. (2) 1/4 X 1.50 X 2.00 Block
2
Qty. (3) 1/2 Lock Washer
3
Qty. (2) 1/2-13 X1.50 GR5 Bolt
4
Qty. (1) 1/2-13 Hex Nut
5
Qty. (1) 1/2-13 X 2.00 GR5 Carriage Bolt
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2005, 2007, 2009 Cequent Performance Products
Installation Instructions
Chevrolet Venture & Uplander
Pontiac Trans Sport & Montana & SV6
Buick Terraza
Oldsmobile Silhouette
Fascia
Exhaust hanger installed through this slot
on Buick & all wheel drive models. See
figures 2 &3
Existing weldnuts (may be
hidden by compressor bracket,
drill clearance hole in bracket
for M10 bolt)
Short wheel base frame rails
shown
Saturn Relay
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location:
* Use only on short wheel base
(on 2004 and older only)
Use here on short wheel base
(on 2004 and older only)
Use here on long
wheel base (on 2004
and older only)
Existing weldnut (used
to mount compressor)
2005 & newer
Drilled
hole
Note: Some bolts or blocks will not be used depending on vehicle application.
* only on short wheel base
6
Qty. (5) M10 X 1.50 X 45mm CL 9.8 Bolt
7
Qty. (2) 1/2-13 Handle Nut Assembly
8
Qty. (1) 1/4 X 1.50 X 2.00 Block
9
Qty. (1) U-Block
Qty. (4) 1/4 X 2.00 X 2.00 Block
Sheet 1 of 6
Part Numbers:
75133
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5000 (2270 Kg)
3500 (1589 Kg)
Fishwire through slot
Existing slot (on older short wheel
base) drilled hole on 2004 & older
long wheel base
Existing weldnut (on 2005 &
newer)
Figure 1
75278N 10-26-09
75278
33094
87410
44574
(U-Haul)
Max Tongue
WT (LB)
500 (227 Kg)
350 (159 Kg)
Rev. G