Cadet TEN Serie Guide D'utilisation

USER'S GUIDE USER'S GUIDE
TEN SERIES TEN SERIES
ELECTRONIC LINE VOLTAGE ELECTRONIC LINE VOLTAGE
THERMOSTAT THERMOSTAT
IMPORTANT INSTRUCTIONS
This product must be installed by a qualified electrician.
In order to avoid fire, shock or death, shut off power supply at the circuit
breaker or fuse before wiring.
Before you begin:
• Verify that the heating appliance that is being connected is within the
specified load range.
• Confirm voltage is within the device rating.
• For wiring, use copper conductors only.
• Mount on a certified electrical box only.
Keep this user's guide in a safe place for future reference.
TECHNICAL SPECIFICATIONS
TEN252DW TEN362DW
Max. load (at 120/240V) 1500 W / 3000 W 1800 W / 3600 W
Max. Amps 10.4 A 15 A
Electrical Rating 120/208/240 V 50-60Hz
Compatible with electric fan-forced or convection
Heater Compatibility
heaters and baseboards
Programmable 5 °C - 30 °C (41 °F - 86 °F)
Temperature range Storage -40 °C - 70 °C (-40 °F - 158 °F)
LCD may degrade at 0 °C (32 °F)
Wiring 4 Wire, Double pole
Software Class A
Certification cULus
Impulse Voltage 2500
Pollution Degree PD2
FCC/IC Class B
TECHNICAL SUPPORT
Thank you for your purchase! Question or problem? Let us solve it
with a single phone call, email or online chat! We'll save you a trip
back to the store!
Cadet Customer Service
Phone: 855.223.3887 (from the US)
800.668.6663 (from Canada)
email: customerservice@cadetheat.com
Live chat: cadetheat.com (contact us)
7216290200R00
INSTALLATION
WIRING INSTRUCTIONS
1. Connect the black 'L1' thermostat wire to the live supply wire.
2. 240V: Connect the red 'L2' thermostat wire to the other live supply wire.
120V: Connect the red 'L2' thermostat wire to the neutral supply wire.
3. Connect the black 'Load' wire to the live heater wire.
4. 240V: Connect the red 'Load' thermostat wire to the other heater wire.
120V: Connect the red 'Load' thermostat wire to the neutral heater wire.
To power supply To power supply
L1 L1
L1 L1
Load Load
L2 or L2 or
L2 L2
Neutral Neutral
To heater To heater
MOUNTING THE THERMOSTAT
The thermostat should be mounted after the wiring connections have been
connected.
1. Remove the small screw at the bottom of the thermostat using a Philips
#1 screwdriver.
2. Carefully insert a small flat head screwdriver in the slot between the
faceplate and the gray bezel, and gently pry apart.
3. Position the thermostat over the junction box, and secure it using the two
supplied screws.
Note: The protruding box on the back of the thermostat should be
recessed in the junction box.
4. Reinstall the faceplate and insert the previously removed screw.
5. Remove the protective film before use.
Insert small flat head
screwdriver here
CONTROL
DISPLAY
Standby (OFF)
Lock
Heat Mode
Temperature
(Fan, Convection/
Display
Baseboard)
Temperature
SETUP
Temperature Display
To convert the temperature display:
+ -
1. Press and at the same time.
-
2. Press once. °C or °F will flash.
+
3. Press to change the temperature display.
4. The display will blink for 3 seconds before returning to the main screen.
Heat Mode
Select the mode that applies to your heater: If the incorrect setting is chosen,
your heater may short cycle or hold an inconsistent temperature.
+ -
1. Press and at the same time.
-
2. Press twice. or will flash.
+
3. Press to change the heat mode.
Select for fan-forced heaters or for convection heaters (including
baseboard heaters.)
4. The display will blink for 3 seconds before returning to the main screen.
FUNCTIONS
Setting the Temperature
The display will show the ambient temperature, except during temperature
adjustment, in which case it will show the set temperature. To adjust the set
temperature:
+ -
1. Use or to select the desired temperature.
2. The display will blink for 3 seconds before returning to the main screen.
In case of loss of power, the thermostat will retain the temperature setting.
Lock Function
Use the lock function to prevent the settings from being changed
inadvertently.
To enable:
+ -
1. Press and at the same time.
-
2. Press 4 times. The icon will appear.
+
3. Press to enable the lock function. The display will blink for 3 seconds
before returning to the main screen.
The icon will remain visible to indicate that the lock function is enabled.
+ -
To disable, press and hold and .
Standby (OFF)
Use the standby function to turn the heater off indefinitely.
+ -
1. Press and at the same time.
-
2. Press 3 times. The icon will blink.
+
3. Press to enable the standby function. The will remain solid to indicate
that it is enabled.
4. The display will blink for 3 seconds before returning to the main screen.
The will remain visible, indicating that the standby function is enabled.
+ -
To disable, press and hold and .
WARRANTY
If the thermostat is deemed defective within 3 years of the
original date of purchase, Cadet will repair or replace the
product at its discretion.
Warranty is void in case of damage incurred from improper use
or installation.
See http://cadetheat.com/product-warranty for details.
I
n keeping with our policy of continuous product
improvement, we reserve the right to make
changes without notice.
© 2020 Glen Dimplex Americas