Assembly - Black Max BM10680 Serie Manuel De L'opérateur

LOOSE PARTS LIST
See Figure 2.
The following items are included with the generator:
Key
No. Description
1 Axle ......................................................................2
2 Retaining Pin .......................................................2
3 Cover ...................................................................1
4 Wheel ...................................................................2
5 Switch Key ...........................................................2
6 Handle Lock Pin ..................................................2
7 Lanyard ................................................................2
8 Nut (1/4-20) .........................................................2
9 Washer (1/4 in.) ....................................................2
10 Rubber Foot ........................................................2
11 Bolt (1/4-20 x 1-1/2 in.) .......................................2
12 Nut (5/16-18) .......................................................2
13 Washer (5/16 in.) ..................................................4
14 Bolt (5/16-18 x 1 in.) ............................................2
15 Frame Support ....................................................1
16 Engine Lubricant..................................................1
17 Bolt (5/16-18 x 2-1/4 in.) .....................................2
18 Lock Nut (5/16) ....................................................2
19 Handle .................................................................2
20 Handle Bracket Spacers......................................2
Operator's Manual (not shown) ...........................1
TOOLS NEEDED
See Figure 3.
The following tools (not included or drawn to scale) are
needed for assembly:
 7/16 in., 1/2 in., and 9/16 in. Socket Wrench
 7/16 in., 1/2 in., and 9/16 in. Combination Wrench
UNPACKING
This product requires assembly.
 Carefully cut the box down the sides then remove the
machine and any accessories from the box. Make sure
that all items listed in the packing list are included.
NOTE: This machine is heavy and requires a minimum of
two people to lift. To avoid back injury, lift with your legs
and not your back.
WARNING:
Do not use this product if any parts on the Loose Parts
List are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer instal-
lation. Use of a product that may have been improperly
assembled could result in serious personal injury.
 Inspect the unit carefully to make sure no damage oc-
curred during shipping.

ASSEMBLY

 Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
 If any parts are damaged or missing, please call
1-800-726-5760 for assistance.
Qty.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not attempt to operate the generator until assembly
is complete. Failure to comply could result in possible
serious personal injury.
NOTE: Do not put fuel or lubricant in the generator before
installing the feet, frame support, and wheels.
INSTALLING FEET ON THE FRAME SUPPORT
See Figure 4.
 Locate the following items:
2 rubber feet
2 lock nuts (1/4-20)
2 washers (1/4 in.)
2 bolts (1/4-20 x 1-1/2 in.)
 Insert bolt through foot, then through frame support as
shown.
 Thread washer over the bolt, then install nut. Tighten nut
securely.
NOTE: Be careful not to overtighten so that foot material
collapses.
 Repeat with remaining foot.
INSTALLING THE FRAME SUPPORT
See Figure 4.
Install the frame support on the bottom of the generator
frame on the same side as the handle.
 Locate the following items:
Frame support
2 flange nuts (5/16-18)
4 washers (5/16 in.)
2 bolts (5/16-18 x 1 in.)
 Raise the end of the generator where the recoil starter is
located high enough to gain access to the frame bottom;
securely position props underneath to support.
 Align the holes on the frame support with the holes on the
generator frame.
Page 11 — English