Installation Diagram; Installation Precautions; Precautions For Use - SIHOO M86C Manuel Utilisateur

User Manual

Installation diagram

（subject to actual size）
1 Press the wheel into the foot of 2 Put the air pressure rod into the
the chair. middle hole of the chair leg.
Front side
Connect the cushion and the mechanism 5 Connect the backrest and seat
4
with 4 M6 * 35 mechanism screws and cushion with 3 M8*40 backrest
small gaskets, pay attention to the front screws, large gasket and spring
and back directions. pad.
7 Press the decorative box into the
Connect the headrest and backrest
8
headrest frame.
with 2 M6 * 20 headrest screws.
Function icon
（subject to actual size）
Press the button to pull up
the armrest to adjust the
height of the armrest.
The handle can be raised and
lowered to adjust the lift of
the chair. When pulled out,
the chair can be tilted back.
Front side
3 Connect the armrest and seat
cushion with 6 M6 * 35 armrest
screws.
6 Align the upper part of the
assembled chair with the air
pressure rod.
SIHOO
Adjustable headrest
Adjustable waist pillow
Backward elasticity adjustment
_
tightening loosening
+

Installation Precautions

1. Please read the installation instructions (picture) of all accessories carefully before installation, and master the
installation steps and methods.
2. Check whether the accessories are complete and damaged.
3. To avoid injury during installation, it is recommended that you wear gloves.
4. Choose a spacious and clean site when installing. The paper is laid flat on the ground; so as to prevent the components
from colliding with the ground during installation.
5. Please note that once the pneumatic rod is installed, it is more difficult to remove.
If you need to remove the chair when you are moving, etc., use a rubber-headed hammer to gently tap the head of the
pneumatic rod multiple times, and then remove the base. Then continue to tap lightly to the five-star foot, using the
principle of vibration to make the air pressure bar fall off. Since it needs to be done with tools, please be careful not to get
injured.
(Damage and accidents caused by this operation are not covered by the product warranty, please be careful)

Precautions for use

1. Please note that this product is designed for single seat and can only be used by one person. Using more than 2 people
will damage the stability of the product and is dangerous. Children under 5.5 years old should use it under the supervi-
sion of an adult.
2. To avoid using the wrong screws, please fix all the screws before tightening them.
3. For the use of product features, please follow the instructions displayed on the product features.
4. This product can only be used when all screws and components are locked. Check the locking screws and components
at least every 3 months.
5. Please put it on a flat ground when using it. Please avoid using it in damp or pyrotechnic areas. Please avoid direct
sunlight for a long time.
6. This product is only for riding, please do not step on the chair or sit on the armrest, it is easy to cause damage to the
chair and danger.
7. After installation, please use soft velvet cloth to remove the dust and dirt indicated by the furniture.
8. For your safety, it is strictly prohibited to disassemble the pneumatic rod.
Accessories table
（subject to actual size; one for each model of screw and washer)
5 wheels 1 chair leg
1 cushion 1 backrest
3 + 1 large gaskets
1 headrest
Mechanism / armrest screws (M6 * 35) 10 + 1
0 1 2 3 4
Note: Before installing the chair, please classify the screws and measure the length of the
screws for installation.
1 institution 1 pair of armrests
1 pneumatic bar
4 + 1 small gaskets
SIHOO
1 decorative cover Spring pad: 3 + 1pcs
Headrest screws (M6 * 20) 2 + 1 Backrest screws (M8 * 40) 3 + 1
1 hex wrench (5MM) 1 hex wrench (4MM)
5 6 7 8 9 10 cm