nedis WCPD20W102BK Guide De Démarrage Rapide

a
Quick start guide
USB-C Wall Charger
For more information see the extended manual online:
ned.is/wcpd20w102bk | ned.is/wcpd20w102wt
Intended use
The USB wall charger is intended to charge tablets, smartphones
and many other USB devices, without requiring a PC or notebook.
The USB charger converts voltages from 100 to 240 VAC into 5.0
VDC - 12.0 VDC and is very convenient at offices, at home or during
travels.
The product is intended for indoor use only.
The product is not intended for professional use.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Specifications
Product
Article number
Input voltage
Input AC frequency
Output voltage
Output current
Output power
Average active efficiency
Efficiency at low load (10 %)
No-load power consumption
Main parts (image A)
1
USB charging port
Safety instructions
WARNING
-
• Ensure you have fully read and understood the instructions in this
document before you install or use the product. Keep the
packaging and this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace a
damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
• Do not expose the product to water or moisture.
• Disconnect the product from the power source and other
equipment if problems occur.
• Always check that the voltage of the product corresponds to the
mains voltage.
• Do not unplug the product by pulling on the cable. Always grasp
the plug and pull.
• Unplug the product when your device is charged or if you do not
plan on using the product for an extended period of time.
• The power outlet shall be located near the product and shall be
easily accessible.
• Never use a damaged or faulty USB cable for charging. This this
can damage the product and harm your device.
• Stop the charging process if the product gets too warm.
Using the product
1. Connect the charger into the power outlet.
2. Insert a USB cable into the USB charging port and the other end
to the device you want to charge.
3. Unplug the charger when it is not in use.
c
Kurzanleitung
USB-C Wandladegerät
Weitere Informationen finden Sie in
der erweiterten Anleitung online:
ned.is/wcpd20w102bk | ned.is/wcpd20w102wt
Bestimmungsgemäße Verwendung
Das USB-Wandladegerät ist zum Aufladen von Tablets, Smartphones
und vielen anderen USB-Geräten gedacht, ohne dass ein PC oder
Notebook erforderlich ist. Das USB-Ladegerät wandelt Spannungen
von 100 bis 240V in 5,0 VDC - 12,0 VDC um und ist sehr praktisch in
Büros, zu Hause oder auf Reisen.
Das Produkt ist nur zur Verwendung innerhalb von Gebäuden
gedacht.
Das Produkt ist nicht für den professionellen Einsatz gedacht.
Jegliche Modifikation des Produkts kann Folgen für die Sicherheit,
Garantie und ordnungsgemäße Funktionalität haben.
Spezifikationen
Produkt
Artikelnummer
Eingangsspannung
Eingangs-AC-Frequenz
Ausgangsspannung
Ausgangsstrom
Ausgangsleistung
USB-C Wall Charger
WCPD20W102BK / WCPD20W102WT
100 - 240 VAC
50/60 Hz / 0.5 A
5.0 VDC / 9.0 VDC / 12.0 VDC
3.0 A / 2.22 A / 1.67 A
15 W / 20 W / 20 W
84.68 %
79.18 %
0.052 W
USB-C Wandladegerät
WCPD20W102BK / WCPD20W102WT
100 - 240 VAC
50/60 Hz / 0,5 A
5,0 VDC / 9,0 VDC / 12,0 VDC
3,0 A / 2,22 A / 1,67 A
15 W / 20 W / 20 W
WCPD20W102BK /
WCPD20W102WT
WCPD20W102BK /
WCPD20W102WT