Using The Product - Philips 3000 Serie Mode D'emploi

Using the product

Switching the product on and off
1 To switch on the product, slide the on/off slide
upwards. (Fig. 7)
2 To switch off the product, slide the on/off slide
downwards. (Fig. 8)
Detaching and attaching the attachments
Note: Switch off the product before you detach or
attach the attachments.
1 To detach the trimming head from the handle,
firmly grasp the attachment below the cutting
element and turn it until the setting indicator
points to the 'unlocked' indication (^).
2 Lift the attachment off of the handle. (Fig. 9)
1 To attach the trimming head to the handle,
place the attachment on the handle with the
setting indicator pointing to the 'unlocked'
indication (^).
Firmly grip the attachment below the cutting
element and turn it until the setting indicator
points to the 'locked' indication (0).
Tip: If the trimming head becomes clogged, detach
the trimming head and rinse it thoroughly with
warm water before you reattach it.
Trimming eyebrows with the eyebrow
guard
1 Comb your eyebrows in the direction of hair
growth (Fig. 10).
2 Make sure the product is switched off. Slide the
eyebrow comb onto the trimming head (Fig. 11).
The short eyebrow comb trims the hairs to a
length of 3 mm (1/8 in). The long eyebrow comb
trims the hairs to a length of 5 mm (13/64 in).
Note: Make sure the comb slides into the
grooves on both sides of the trimmer.
3 Switch on the product.
4 Move the comb over the eyebrow from the
outer tip of the eyebrow towards the base of
the nose (against the direction of hair growth)
(Fig. 12).
5 Clean thoroughly after each use (see 'Cleaning').
Trimming ear hair
Make sure your outer ear channels are clean and
free from wax.
Note: If there is an eyebrow comb on the trimmer
head, remove it before trimming nose or ear hair.
(Fig. 13)
1 Switch on the product.
2 Slowly move the trimming head along the rim of
the ear to remove hairs that stick out beyond
the rim.
Do not insert the trimming head more than
5mm (13/64 in) into your ear channel, as this
could damage the eardrum.
3 Carefully insert the trimming head into the
outer ear channel.
4 Slowly turn the trimming head around to
remove all unwanted hairs from your outer ear
channel (Fig. 14).
5 Clean thoroughly after each use (see 'Cleaning').
Trimming nose hair
Make sure both the product and nasal passages
are clean before trimming. Dried nasal mucus can
block the cutting element, preventing the product
from turning on.
Note: If there is an eyebrow comb on the trimmer
head, remove it before trimming nose or ear hair.
(Fig. 13)
1 Switch on the product.
2 Slowly move the trimming head along the rim of
the nostril to remove hairs that stick out beyond
the rim.
3 Carefully insert the trimming head into one of
your nostrils. (Fig. 15)
Do not insert the trimming head more than
5mm (13/64 in) into your nostrils.
4 Slowly move the trimming head around inside
each nostril, making sure the side of the
trimmer is held firmly against the skin. (Fig. 16)
This will reduce the tickling effect that can
occur.
5 Clean thoroughly after each use (see 'Cleaning').
Cleaning
Cleaning the trimming head
Do not immerse the motor unit in water or any
other liquid, or rinse it under the tap.
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as gasoline or acetone
to clean the product or any attachments or
accessories.
Do not tap on the cutting elements.
Do not use any sharp objects to clean the cutting
elements.
Clean the trimming head immediately after use
and when a lot of hair or dirt has accumulated on
the cutting elements.
1 Rinse the cutting element of the trimming head
with hot water.
2 Switch on the product and rinse the cutting
element and trimming head again (Fig. 17) to
remove any remaining hairs. Then switch off the
product again.
Tip: If rinsing the trimming head under the tap is
not sufficient, immerse the trimming head in a
glass with warm water for a few minutes (Fig.
18). Then switch on the product and rinse it
under the tap.
3 Rinse the combs with lukewarm water (Fig. 19).
4 Carefully shake off excess water and let all parts
air dry.
Storage
Store the product in a safe, dry location, using the
pouch provided. Make sure that the product and