Manuels Connexes pour Granberg Baselift Corner 6311H
Sommaire des Matières pour Granberg Baselift Corner 6311H
- Page 1 Dok. Nr: M6311-ETL V: 1.0 2021-10-04 Installation Instructions / Instructions d’installation Baselift Corner 6311H / 6311L 6311H 6311L 1,6” 4.1” WWW: Baselift Corner 6311...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS / PRESCRIPTIONS DE SÉCURITÉ IMPORTANTES EN When using an electrical furnishing, basic precautions should always be followed, including the following: Read all instructions before using the BASELIFT. DANGER - To reduce the risk of electric shock: 1. Always unplug this furnishing from the electrical outlet before cleaning. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1.
- Page 3 Technical data / Données techniques EN Thank you for choosing to install a product from Granberg! In order for the product to work safely and securely, it is extremely essential that the installation instructions be followed. The installer should read and understand all the installation instructions before installation begins.
- Page 4 Planning / Planification EN Very Important! Check floor stability before installation. Maximum load on lifting unit is 220 lb (100kg) and dead load up to 220 lb (100kg). Ensure that the wall can withstand the concentrated load that occurs under motor units. Make sure that the motor units can be fixed to the wall and that the structure is not porous.
- Page 5 Electricity and Water / Électricité et eau EN The lifting unit requires two power outlets and consumes a maximum of 10 A (5 A+5 A). (mm) If the counter has a sink, the connections for electricity, water and drain should be placed centrally below the mixer. The electrical connection can also be placed in a protected position inside a motor unit.
- Page 6 Content of delivery / Contenu de la livraison 4x BR M6x16 4x M6 2x M8X45 4x M6 x 60mm 16 mm 2x M8 6x M8x16mm Accessories / Accessoires 16 mm 48x 3x12 mm 16 mm 24x 3x16 mm 8x M6x12...
- Page 7 R I G H T ( R ) 36.6” (930mm) CL960...
- Page 8 CL960...
- Page 9 16 mm 6x M8x16mm CL960...
- Page 10 HEX 5/32” BR M6x16 4x M6 4x M6 x 60mm Anti-pinch strip Bande anti-pincement CL960...
- Page 11 CL960...
- Page 12 CL960...
- Page 13 CL960...
- Page 14 22.04” - 23.2” (560 - 590mm) CL960...
- Page 15 10 mm 2x M8X45 2x M8 CL960...
- Page 16 CL960...
- Page 17 CL960...
- Page 18 230V WARNING – Ensure both power supply cords are connected before use AVERTISSEMENT – Avant utilisation, assurez-vous que les deux cordons d'alimentation sont branchés CL960...
- Page 19 B - 0.157” (4mm) 2.36” (60mm) 0.787 (20mm) > 4” > 2.3” 0.866” (22mm) 1.42” (36mm) For drawer Pour tiroir DWG NO. 10433 REVISION Granberg Interior AB Tel. +46(0)11197750 info@granberg.se TITLE: Frontfästen www.granberg.se DWG NO. 10433 REVISION T I T DRAWN MATERIAL:...
- Page 20 min 0.2” (5 mm) min 0.2” (5 mm) CL960...
- Page 21 CL960...
- Page 22 CL960...
- Page 23 8x M6x12 HEX 1/8” CL960...
- Page 24 1.38” (35mm) 1.38” (35mm) 5.9” (150mm) 16 mm 16 mm 3x- 3 x 16 mm 3x- 3 x 16 mm DWG NO. REVISION 08473 Granberg Interior AB Tel. +46(0)11197750 Tel. info@granberg.se TITLE: info Täckskiva nedre 45-90 www.granberg.se DRAWN MATERIAL: FINISH:...
- Page 25 16 mm 12x 3 x 16 mm 1045 L - 0.39” (10 mm) / R - 0.39” (10 mm) 35.3” (897mm) 1x L + 1x R 560 - 590 Granberg Interior AB Tel. +46(0)11197750 info@granberg.se www.granberg.se 1.38” (35mm) 5.9” (150mm) DRAWN...
- Page 26 16 mm 8x 3 x 12 mm 0.315“ 8 mm CL960...
- Page 27 0.98” (25 3.85” (98mm) 3.85” (98mm) 0.315” (8mm) 0.315” (8mm) 0.315” (8mm) 0.315” (8m DWG NO. DWG NO. REVISION 08474 0847 Granberg Interior AB Granberg Interior AB Tel. +46(0)11197750 Tel. +46(0)11197750 info@granberg.se info@granberg.se TITLE: TITLE: Täckskiva övre 45-90 Täc www.granberg.se www.granberg.se...
- Page 28 6x 3 x 16 mm 1045 L - 0.39” (10 mm) / R - 0.39” (10 mm) 0.98” (25mm) 0.98” (25mm) 0.315” (8mm) 560 - 590 1x L + 1x R Granberg Interior AB Tel. +46(0)11197750 info@granberg.se www.granberg.se DRAWN MATERIAL: CHECKED WEIGHT:...
- Page 29 16 mm 8x 3 x 12 mm CL960...
- Page 30 Adjustment / Ajustement Leveler Niveleur...
- Page 31 Adjustment / Ajustement 9/16”...
-
Page 32: Functional Tests
Functional tests Complete functional tests should be carried out after installation: Ensure both power supply cords are connected before use! Test run the lift unit up and down all the way to each end position. Make sure that the lift runs freely without obstacles, risk of pinching and noise. - Page 33 Before you use the device - Read the users manual Only authorized persons may use the this product! Authorization means obligation to read and follow the instructions. It is very important that you read and understands the users manual before you use the device. The user manual is attached as a separate booklet.
- Page 36 Granberg Interior AB Box 6112 600 06, Norrköping Tel: 011-19 77 50 E-mail: info@granberg.se Internet: www.granberg.se...