Technical Specifications - Door-Systems DIP-N-868 Manuel D'installation Et D'utilisation

ENGLISH
The device is designed for the remote control of
au-tomatic doors. The direct application with Door-
Systems automation
control system (the application is similar to
the remote control AT-4N-868). For other
automation models use the external radio
receiver AR-1-500N-868.
It is a two-channel radio transmitter, which is ac-
tivated after typing a certain combination (code)

1. TECHNICAL SPECIFICATIONS

Battery
........................................................
Average service life of battery
Working frequency, MHz
Transmittance power, mW
Operating range
...............
35 m inside the premises (no line of sight)
Number of digits in the combination
Time of auto sleep mode, secs
Enclosure class
........................................................
Outside temperature, ° C
Dimensions, mm
.......................................
Weight, g
....................................................................
Y
The company reserves the right to introduce chang-
es to this manual and the product design without
prior notice, while maintaining the same functional-
ity and purpose. The content of this manual cannot
be used as a grounds for legal claims. The operation
range can be 25–30 % less with a low battery.
2. INSTALLATION
Y
The installation location should provide high-quality
reception of the radio signal (no screening and re-
flecting surfaces or other sources of radio emission).
Make sure that the installation location corresponds
to the specified temperature operating range. Place
the keyboard within visual range of the controlled
equipment (doors), at a height of at least 1.5 meters.
After you are sure of the functionality, install the
radio code keyboard. Secure the mounting brack-
et (fig. 1) and install the keyboard on it (fig. 2). The
keyboard must be easily installed and removed from
the mounting bracket. Do not press down the brack-
et firmly on the installation surface, the surface of
the installation should be flat.
2
with the new radio
battery type
CR2450 3В DC / 580 mАh
2 years
.........................
with 10 transmissions / day
868.35 ± 0.15
.......................
0.1
......................................
100 m in the open space,
from 0 to 8
....
(99,999,999 combinations)
5
..................................
IP54
− 20 ... + 55
...........................
83 × 116 × 22
300
3. USE
The use of the radio code keyboard is based on
'digit combinations' with digits from '0' to '9' that
must be typed by the user. When the combination
is typed, the user presses one of the confirmatory
button  ( 1 channel) or  ( 2 channel) to transmit
a control command (radio signal).
The keypad informs the user about the operation
status by audio signals (table 1).
AUDIO SIGNAL
1 short signal
(tone signal)
1 long signal
5 short signals
1 quiet signal after
button operation
The keypad has the same digit combination (the
same code) for the  and  channel activation.
The factory setting of the digit combination of
channel 1 () and channel 2 () is 1234. To avoid an
unauthorized control, change the digit combination
of the channel code (table 2).
AUDIO SIGNAL
1
Press '0' and hold
2 
Press and release
3 Release '0'
Enter the current (original)
4
combination and press
Enter a new combination
5
(up to 8 digits) and press
Enter a new combination
6

again and press
If the digit combination was not typed when re-
cording a new channel code (no protection from
external control), the command from the radio code
keyboard will be implemented by a simple pressing
of the button  o r .
Y
When the code changing the maximum number
and different the combination digits will provide
the high access security. Keep your personal code
in a safe place in case of need.
When typing a combination, the interval between
pressings should not be greater than 5 seconds. If
this time has been exceeded, you should type the
combination again from the beginning. If you press
the wrong digit by mistake when typing a combina-
tion, you must immediately press the button  o r ,
then an error warning signal will sound (5 short
signals), and you can type the correct combination
again. If you have forgotten the digital code com-
bination, contact the service of an official supplier.
Table 1
DESCRIPTION
Button operation when typing
a combination
Right combination
Error when typing
(or combination change)
Low battery signal.
Battery must be replaced
Table 2
DESCRIPTION
1 short signal
1 long signal
—
Short signals when
 pressing
Short signals when

pressing;
1 long signal when

last pressing
DIP-N-868