Oplink TripleShield Guide D'installation page 3

Installationsanleitung Step Guide
3
STEP
Internet
(C)
Router
(B)
(Not included)
(D)
(A)
Assemble the OPU station and connect to a
DHCP-enabled router
Assemble the system according to the provided picture. It
is recommended that the OPU be placed on a 3-5ft (0.91-
1.52m) high platform.
Note: Once the OPU is up and running, to establish proper connection to it,
power up the remaining devices within 5 feet of the OPU. When connection
is established and working, the devices can be moved to their desired
locations.
7
STEP
(H) Installa on des ba eries Mount Motion Sensor
Montez le Capteur
du capteur de mouvement
de Mouvement
(H) Installa on des ba eries Montez le Capteur
Note: Once Motion sensor alarms, it will start
du capteur de mouvement de Mouvement
(H) Motion Sensor Battery
to count 3 minutes, and count over again if
Installation
any movement detected in this period .The
next alarm will be triggered only when no
movement is detected within 3minutes.
Place the Motion Sensor
Lift the top tab to remove the cover and install the battery
into the Motion Sensor. For maximum coverage, the
sensor should be placed in the corner of the room to be
monitored and no more than 7 feet above the ground. The
Motion Sensor is most effective in areas such as hallways
and entry points where possible intruders will have to pass
through.
4
STEP
The camera can be
moved and mounted
(F)
after the initial activation.
(E)
Power up the IP Camera
Plug the IP Camera into an outlet within 5 feet of the OPU
to establish connection. Once connection is established
and working, the IP Camera can be moved to its desired
location.
Note: Should the placement of the camera cause the image to be upside-
down, use the Flip feature in the App to correct this matter. Video > Single
Video Mode > Image Setting.
8
STEP
( I )
Power up the Siren
Plug the Siren into an outlet within 5 feet of the OPU to
establish connection. Once connection is established and
working, the Siren can be moved to its desired location.
Your Siren comes with a backup battery pre-installed. To
make use of the backup battery, pull and remove the clear
plastic strip to initiate battery contact.
5
STEP
(Sample of QR Code)
Note: When the activation process
cannot be completed normally, the
App will ask you to scan the OPU's
QR code, located on the back of the
OPU, to continue.
Start devices activation on the app
Tap the"Activate Now" button. (Activation process takes
approximately 2 minutes)
9
STEP
Congratulations!
You have successfully installed
the security system!
Activation completed
When you see the "System is ready!" message, your system
is ready for use.
Note: Your IP Camera status will be updated after 10 minutes.
6
STEP
Montez le capteurde porte Montez le capteur de Fenêtre
1/4 de pouce
1/4 inch Max
Montez le capteurde porte Montez le capteur de Fenêtre
1/4 de pouce Montez le capteurde porte Montez le capteur de Fenêtre
1/4 de pouce (0,64 cm)Max Mount Door Sensor Mount Window Sensor
(0,64 cm)Max
(0,64 cm)Max
Note: For the Door/Window Sensor, it does not matter
which piece you place on the frame and which piece
you place on the moving part. To creat proper contact,
ensure the tops of the two pieces line up. The Spacer is
(G)
Installa on des ba eries des
used in situations where the smaller piece needs to be
(G)
Installa on des ba eries des
(G) Door/Window Sensor capteurs de porte/fenêtre
(G)
Installa on des ba eries des elevated to the larger piece to ensure proper contact.
capteurs de porte/fenêtre
Battery Installation
capteurs de porte/fenêtre
Place the Door/Window Sensor
Each Door/Window Sensor set consists of two pieces. Take
the larger piece and with slight force, push the small tab on
the back plate outward and slide the back plate upward.
Remove the back plate and insert a battery into each Door/
Window Sensor set. Apply the double-sided tape to each
piece. It is recommended that the Door/Window Sensor be
mounted in a vertical/upright position.
Add-on Devices
IP Camera Siren Motion Sensor
Door/Window Remote Panic Button Smart Plug
Sensor Control