Vanderbilt IRCW6-12 Instructions D'installation

IRCW6-12
Remote Control
Télécommande
STEP: A6V10327163_b
Edition: 04.04.2016
P/N: 7102013 rev. A
English
Before starting to install and work with this device, please read the Safety
Instructions.
Enrollment and testing
To enrol the IRCW6-12 into the control panel or gateway, follow the instructions
of the corresponding installation/configuration manual.
Since IRCW6-12 is supplied with the battery already installed, the unit is
practically ready to be tested.
Press a key on the IRCW6-12: verify that the transmit LED lights.

Make sure that the control panel responds as programmed and as stated in

the installation/configuration manual.
Repeat the test at locations where the remote control will be operated under

normal use, in order to ensure the wireless transmission is not blocked by any
walls or large objects, or affected by structural materials.
Functions (fig. 1)
Symb. No. Key/Indicator.
1 ARM
2 STAY
3 DISARM
Additional
4
Function
5 PANIC/SOS
6 Indication Light
Leash insertion (optional, fig. 5-7)
You can clip the leash into a key ring or neck band.
Erase previous enrollment
In order to re-enrol an IRCW6-12 into a new control panel you must first erase
the remote control by pressing at the same time the following keys
until the indication light blinks fast green/red (~5s)
1
5
Description
Sends a Set (ARM) command to alarm
system.
Sends a Part Set (STAY) arm command.
Sends an Unset (DISARM) command.
Activates an assigned function
(e.g. light, garage, door, etc.).
These two buttons pressed together for 2
seconds send a PANIC alarm.
Lights up when transmitting, flashes if
battery is low.
2
6
Battery exchange (fig. 2-4)
In order to change the battery, open the housing (Fig. 2) with a screw driver,
cautiously remove the old battery and replace it with a new one and close the
housing again (Fig. 3&4).
Insert the battery in the battery holder making sure the polarity is correct
(+) (-).
Risk of explosion if battery is replaced by an incorrect type.
Clean the remote control only with a soft cloth or sponge moistened lightly
with a mixture of water and mild detergent and wipe it dry immediately. Also
never use solvents such as kerosene, acetone or thinner. The use of
abrasives of any kind is strictly forbidden.
Technical data
Data protocol
Wireless range
Frequency band
Identification
Control transmission
Power
EMI rejection up to
2 GHz
Battery
Current consumption
Environmental conditions:
Operating temperature
Storage temperature
Humidity (EN60721)
Housing protection
EN60529, EN50102
EC Declaration of Conformity
Hereby, Vanderbilt International (IRL) Ltd declares that this radio equipment
type is in compliance with all relevant EU Directives for CE marking. From
20/04/2016 it is in compliance with Directive 2014/30/EU (Electromagnetic
Compatibility Directive) and Directive 2014/35/EU (Low Voltage Directive).
From 13/06/2016 it is also in compliance with Directive 2014/53/EU (Radio
Equipment Directive).
The full text of the EU declaration of conformity is available at:
http://pcd.vanderbiltindustries.com/doc/wireless.
Complies with : EN 50130-4:2011; EN 61000-6-3:207/A1:11; EN 301 489-1
V1.9.2; EN 301 489-3 V1.6.1, EN 300 220-2 V2.4.1, EN 60950-1:2006 +
A11:2009 + A1:2010 + A12:2011 + A2:2013, EN 62479.
For more detailed instruction please refer to the manuals of the respective
control panel or gateway.
3 4
7
Installation Instruction
Si2Way
100 m in open space
868 MHz
Unique ID serial number – 24 bit
Arm, Stay, Disarm, Optional Control, Panic
Automatic Power Saver – Low Bat Indication
(LED flashing) below 2.4 V
> 10 V / m
Battery Lithium 3 V - type: CR2032
Standby: < 1A
-10 to +50 °C
-20 to +60 °C
< 85 % r.h., non condensing
IP41 / IK02
max.: < 28 mA