Makita DVC864L Manuel D'instructions page 13

Masquer les pouces Voir aussi pour DVC864L:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
Cancelling tool registration for the
cleaner
Perform the following procedure when cancelling the
tool registration for the cleaner.
1.
Install the batteries to the cleaner and the tool.
2.
Set the stand-by switch on the cleaner to "AUTO".
► Fig.15: 1. Stand-by switch
3.
Press the wireless activation button on the cleaner
for 6 seconds. The wireless activation lamp blinks in
green and then become red. After that, press the wire-
less activation button on the tool in the same way.
► Fig.16: 1. Wireless activation button 2. Wireless
activation lamp
If the cancellation is performed successfully, the wire-
less activation lamps will light up in red for 2 seconds
and start blinking in blue.
NOTE: The wireless activation lamps finish blinking in
red after 20 seconds elapsed. Press the wireless acti-
vation button on the tool while the wireless activation
lamp on the cleaner is blinking. If the wireless acti-
vation lamp does not blink in red, push the wireless
activation button briefly and hold it down again.
Description of the wireless activation lamp status
► Fig.18: 1. Wireless activation button 2. Wireless
activation lamp
The wireless activation lamp shows the status of the wireless activation function. Refer to the below table for the
meaning of the lamp status.
Status
Color
Standby
Blue
Tool
Green
registration
Cancelling/
Red
erasing
(slow: 2 times/sec.)
tool
registration
Others
Red
Off
Wireless activation lamp
Duration
On
Blinking
Cleaner: con-
Tool: 2 hours
When the tool is
running.
20 seconds
2 seconds
20 seconds
When the
wireless acti-
(fast: 5 times/sec.)
vation button is
pressed down.
2 seconds
3 seconds
-
Erasing all tool registrations
You can erase all tool registrations from the cleaner as
follows.
► Fig.17: 1. Stand-by switch 2. Wireless activation
1.
Install the batteries to the cleaner.
2.
Set the stand-by switch to "AUTO".
3.
Hold down the wireless activation button for about
6 seconds until the wireless activation lamp blinks in red
(about twice per one second).
4.
When the wireless activation lamp starts blinking
in red, release your finger from the wireless activation
button. Thereafter, hold down the wireless activation
button again for about 6 seconds.
5.
When the wireless activation lamp starts blinking
fast (about 5 times per one second) in red, release your
finger from the wireless activation button. When the
wireless activation lamp lights up in red and later lights
off, all tool registrations are erased.
NOTE: If the wireless activation lamp does not blink
in red, press the wireless activation button briefly and
try again.
Waiting for the tool registration or the wireless activation function
tinuing
The lamp on the cleaner blinks when the stand-by switch is set in
AUTO. The lamp on the tool blinks when the wireless activation
button is pushed. The lamp on the tool will automatically turn off
when no operation is performed for 2 hours.
The wireless activation of the cleaner is available and the tool is
Ready for the tool registration. Searching the tool to be registered.
The tool registration has been finished. The wireless activation
Ready for the cancellation of the tool registration. Searching the
The tool registration has been cancelled/erased. The wireless
activation lamp will start blinking in blue.
The power is supplied to the wireless unit and the wireless activa-
-
The stand-by switch is not set to "AUTO".
13 ENGLISH
button 3. Wireless activation lamp
Description
is available.
running.
lamp will start blinking in blue.
tool to be cancelled.
Ready to erase all tool registrations.
tion function is starting up.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dvc864lz

Table des Matières