After Using - TZS First AUSTRIA FA-5109-1 Mode D'emploi

2. COOKING
1. After the pan is turned on wait for about 5-10min. When the control lamp is
extinct, you can start to cook.
2. If the food is completely done, the temperature may be kept, by puting the
temperature scale to "keeping warm".
- If the lamp is blinking, this is not an error. The automatic temperature
regulator has good function.
- If you hear noices while using, this is not anerror, the sound comes from the
heater and the heatplate.
- Do not put your hand under the reflector. Do not put any easy inflammable
material on the pizza pan.
USAGE OF THE COVER
Use the cover for cooking pizza, beefsteak, fried
eggs, grilling in aluminium or plastic foil, pan-
cakes, Hamburger, etc. This gives a mild taste. On
roasting of food there will escape vapour between
the heating plate and the cover so be careful when
taking the cover off the pan.

3. AFTER USING

1. After using put the temperature scale to OFF.
2. At first pull the plug out of the socket, then take
out the automatic temperature regulator from the heat
plate. CAUTION: Because the temperature sensor of the
regulator is very hot after using, let the heat plate cool
down before removing the regulator.
3. After cooling cover the mounting of the socket with the hand in order to avoid
water entrance whilst cleaning the plate with a soft sponge.
AFTERAWARDS CLEAN THE COOLED OFF APPLIANCE WITH A DRY AND SOFT
CLOTH.
PREAUTION MEASURES TO OPERATE THE HEAT PLATE
THE SURFACE OF THE HEATPLATE IS NON-STICK COATED, SO TAKE CARE
AS FOLLOWS:
• do not use articles made of metal (if the beefsteak should be cut, put the food on
a different plate)
• do not use a sharp knife to cut the food on the surface
• do not put the automatic temperature regulator on the heat plate. It is not
permitted to have contact with the heat plate
• do not use cleaner, nylon brush or metal brush. The surface of the heat plate
would get damaged
• the plate must be cleaned with a cloth after using. Left over food or oil on the
surface would lead to fire.
4
PRECAUTION MEASURES AND PROPOSALS
Important information for your safety: the following cautions measures must be
followed. To avoid electroshock, fire or function error.
OVERHEATING OF THE CABLES
• please stop using the pan and bring the appliance to the next trader
RIGHT VOLTAGE 220-240V
• the voltage must be 220-240V. After usage, please unplug the appliance.
Do not use an extension cord with several plug sockets
CAREFUL HANDLING OF THE CABLE
• do not let cable hang over edges
• when you disconnect the appliance, please use the plug
DO NOT PUT THE HEATPLATE INTO WATER
• do not clean the heat plate in water
• after cleaning, the heat plate must be dry before you can use the pan again
THE HEATING PLATE MUST NOT BE USED AT THE FOLLOWING PLACES
• on an unsteady place or on inflammable materials (newspaper, paper, etc.)
• the plate must be min. 15cm distance from walls and furniture
THE AUTOMATIC TEMPERATURE REGULATOR
1. The automatic temperature regulator is a highly sensitive part, so you must be
very careful. Do not let the appliance fall down or be exposed to shocks or rough
impacts.
2. Use always the temperature regulator which this appliance supplies. Never use
another regulator.
3. Inserting the automatic temperature regulator you must make sure that the
regulator is put in the right place. If you pull the regulator, do not pull the cable,
catch the plug of the regulator and pull out. Do not use too much force to insert
or pull out.
4. Keep temperature sensor and contacts clean.
5. If the automatic temperature sensor is damaged, immediately switch off the
appliance and stop using it. Bring it to your next trader to repair.
6. Before inserting or pulling the regulator you must guarantee that the scale of the
regulator is turned off.
5