Sommaire des Matières pour BRICK MATEOFIR HF190111
Page 1
: HF190111/MATEOFIR ITEM Important note/Note importante: 1.Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid scratching the parts./Placer les pièces sur une surface propre et lisse tel qu'une couverture ou un tapis pour éviter d'endommager les pièces. 2.Kindly follow the assembly instructions step by step./ Veuillez suivre la notice d’assemblage, pas à...
Page 16
: HF190111/MATEOFIR ITEM STEP 13 / ÉTAPE 13 CC x 6 PAGE 16 OF 21...
Page 17
: HF190111/MATEOFIR ITEM STEP 14 / ÉTAPE 14 E x 4 F x 8 L x 2 M x 4 PAGE 17 OF 21...
Page 18
: HF190111/MATEOFIR ITEM STEP 15 / ÉTAPE 15 F x 16 WARNING: Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the screws and bolts for a good fit. Figure 1: Adjust these 4 screws to adjust the up and down direction of the door. Figure 2: Adjust the bolt to adjust the front and rear direction of the door.
Page 19
: HF190111/MATEOFIR ITEM STEP 16 / ÉTAPE 16 D x 8 PAGE 19 OF 21...
ANTI-TIPPING STRIP INSTRUCTION INSTRUCTIONS POUR SANGLE ANTI-BASCULEMENT HARDWARE INCLUDED TOOLS REQUIRED (NOT INCLUDED) MATÉRIEL INCLUS OUTILS REQUIS (NON COMPRIS) SCREW Ф4×35mm 2 pcs/pces DRILL & DRILL BIT PERCEUSE ET TRÉPAN SCREW Ф4×20mm 2 pcs/pces LIGHT HAMMER WALL ANCHOR MARTEAU LÉGER Ф6×30mm 2 pcs/pces ANCRE AU MUR...
Page 21
: HF190111/MATEOFIR ITEM MAXIMUM LOAD 99.2 lbs (45 kg) CHARGE MAXIMALE 99,2 lbs (45 kg) MAXIMUM LOAD 24.3 lbs (11 kg) CHARGE MAXIMALE 24,3 lbs (11 kg) MAXIMUM LOAD 24.3 lbs (11 kg) CHARGE MAXIMALE 24,3 lbs (11 kg) COMPLETE / ASSEMBLAGE TERMINÉ PAGE 21 OF 21...
IMPORTANT INSTRUCTIONS ASSEMBLY INSTRUCTIONS General 1. Read all instructions before using this appliance. 14. Do not insert or allow foreign objects to enter any 2. This heater is hot when in use. To avoid burns, do not let bare ventilation or exhaust opening as this may cause an electric Keep combustible materials, such as skin touch hot surfaces.
Page 24
ELECTRIC FIREPLACE SPECIFICATIONS 18 x 5 x 17 1/8 inch 45.7 x 12.8 x 43.5 cm 5.8kg / 6.7kg 1400 Watts...
ASSEMBLY INSTRUCTIONS REQUIRED TOOLS HARDWARE Phillips Screwdriver Ф Ф 4 X 10mm 4 X 6mm (not included) AA x 1 BB x 2 CC x 6+2 extra DD x 6+2 extra 1. ATTACHING THE METAL TRIMS 2. INSTALLING THE FIREPLACE INSERT...
Page 26
OPERATING INSTRUCTIONS 1. Identifying the control panel 2. Using the main power button The control panel is located on the top right corner Press the power button (1) to turn the fireplace/heater of the fireplace/heater unit. unit on and off. Press the power button (1) once to turn the unit on.Press again to turn the unit off.
OPERATING INSTRUCTIONS 4. Using the heater control The heater button (3) turns the heater on or off. There is no speed setting for the heater blower. If heater is on when the unit is turned off by the main power button,when the power is turn back on,the heater will come on at the same time.If the heater is off when power is off, the heater will remain off when power is turned back on.
REPLACEMENT PARTS LIST AND EXPLODED VIEW Part Part name Main circuit board Flame generator drive motor Heater / blower assembly Control panel buttons Control panel circuit board Emberbed with log Flame effect circuit board Flame generator / spinner Remote control Some parts and specifications may change without notice.
TROUBLE SHOOTING GUIDE PROBLEM SOLUTION Check that the unit is plugged into a standard 120V outlet. The unit does not turn on. Press the power button on the control panel. The main power switch lights up, but there is Open the top and back panel to check if the flame spindle has fallen off no flame effect.
INSTRUCTIONS cleaning the appliance. REPLACING THE REMOTE DISPOSING OF USED CONTROL BATTERY BATTERIES When the remote control stops operating or its range seems reduced, The batteries may contain hazardous substances that could it is time to replace the battery with new ones. endanger the enviroment and human health.
INSTRUCTIONS IMPORTANTES INSTRUCTIONS DE MONTAGE Généralités 14. Évitez d’introduire ou de faire tomber des corps étrangers 1. Lisez toutes les directives avant d'utiliser cet appareil. dans les fentes d'entrée et de sortie de l'air car cela pourrait 2. La chaufferette devient très chaude lorsqu'elle est en marche. Pour éviter toute brûlure, ne laissez pas la peau non couverte provoquer des décharges électriques, causer un incendie ou endommager la chaufferette.
ENTRETIEN RECOMMANDATIONS À L'UTILISATEUR AVERTISSEMENT 1. Toute réparation de cet appareil ne doit être effectuée que par une N'utilisez pas ce foyer si l'une de ses pièces a été immergée. personne qualifiée. Contactez immédiatement un technicien qualifié pour inspecter 2. Cet appareil ne doit être modifié en aucune circonstance. l'appareil et remplacer des pièces du circuit électrique si besoin.
INSTRUCTIONS DE MONTAGE OUTILS REQUIS QUINCAILLERIE Tournevis Cruciform Ф Ф 4 X 10mm 4 X 6mm (non compris) AA x 1 BB x 2 CC x 6+2 extra DD x 6+2 extra 1. ASSEMBLAGE LES MOULURES DE MÉTAL 2. INSTALLATION DU FOYER ENCASTRÉ...
INSTRUCTIONS D’OPÉRATION 1. Utilisation du panneau de commande 2. Utilisation du bouton d’alimentation principal Le panneau de commande est situé sur le coin supérieur droite du foyer/appareil de chauffage. Appuyer sur le bouton d’alimentation (1) pour activer/désactiver le foyer/appareil de chauffage. Le panneau de commande contient l'alimentation Appuyer sur le bouton d’alimentation (1) une fois pour principale(1), commande de flammes (2),com-...
INSTRUCTIONS D’OPÉRATION 4. Utilisation de la commande de chauffage Appuyer sur la touche chauffage (3) allume et éteint l’effet de chauffage. Il n'existe aucun paramètre de vitesse pour le ventilateur du chauffage. Si la fonction de chauffage est allumée quand vous éteignez l'unité avec l'interrupteur principal, le chauffage s'allumera quand vous rallumerez l'unité.
LISTE DES PIÈCES DE RECHANGE ET VUE ÉCLATÉE Pièce Nom de la pièce Circuit imprimé principal Moteur du générateur de flamme Ensemble Chauffage / Ventilateur Panneau de commande Circuit imprimé du panneau de commande Lit de braises avec bûche Circuit imprimé de l'effet de flamme Générateur de flamme / pièce tournante Télécommande Certaines pièces et caractéristiques peuvent changer sans préavis.
GUIDE DE DÉPANNAGE PROBLÉME SOLUTION S'assurer que l'unité est branchée dans une prise standard de 120 V. Le dispositif ne se met pas en marche. Appuyer sur le bouton d'alimentation sur le panneau de commande. L'interrupteur d'alimentation principal s'allume, Ouvrir le panneau arrière supérieur pour vérifier si la tige de flamme est mais il n'y a pas d'effet de flamme.
DIRECTIVES D'ENTRETIEN foyer. câblage REMPLACEMENT DE LA PILE MISE AU REBUT DES DE LA TÉLÉCOMMANDE PILES USAGÉES Lorsque la télécommande s’arrête de fonctionner ou sa puissance Les piles peuvent contenir des substances dangereuses qui semble réduite, il est temps de remplacer les pile. pourraient mettre en péril l’environnement et la santé...