Battery And Charger - Qonnect Q-TOOL N12XL Manuel De L'utilisateur

Depending on the working mode you choose, the blind rivet nut will be set as follow:
- Manual mode: Press the trigger of the Q-Tool to set the blind rivet nut; the mandrel will
automatically unscrew itself from the set blind rivet nut.
- Automatic mode: The blind rivet nut will be set automatically without any further action.
Immediately after setting the blind rivet nut, the mandrel will unscrew itself automatically
from the set blind rivet nut.
2.2.6 Force reverse button
In case a blind rivet nut is blocked or jammed, the
the blind rivet nut. Press corresponding indicator light flashes) and pull the trigger 1 time
to force the mandrel to exit from the blind rivet nut and reset. This action can be applied in several
cases of fault codes as well.
2.3 Troubleshooting
Problem Possible cause
Blind rivet nut - Incorrect stroke (too low)
is not deformed - The thickness of the workpiece
enough does not match
- Lithium battery undervoltage
Automatic blind - Size of blind rivet nut does not match
rivet nut spin-on the mandrel size of the Q-Tool
function does not - Mandrel worn out
work - Wrong tuning of the protruding
mandrel/anvil
The mandrel - The thread of the blind rivet nut is
is stuck in the damaged or defective
workpiece - The mandrel is damaged, or the
wrong size mandrel is used
The mandrel broke - Stroke too high
- Single side force on the mandrel
The Q-Tool has no - Empty battery or battery worn
movement out / damaged
- Riveting capacity beyond Q-Tool
capacity
Fault code Description
E1 Communication failure
E2 Power overload
E3 Blind rivet nut jammed / blocked
E4 Stroke failure
E5 Electrical circuit overheated
E6 Motor overheated
NOTE: if the solutions provided above have no effect, the tool must be repaired by qualified
personnel or returned to the dealer or manufacturers' representative.
- -
8
button helps to reverse the mandrel out of
Solution
- Increase stroke
- Check blind rivet nuts, and the
plate thickness
- Charge battery or replace with
a charged battery
- Change to correct blind rivet
nut, or change to correct mandrel
- Replace the worn out mandrel
- Tune the length of the protruding
mandrel/anvil correctly
- Replace the blind rivet nut with
one that is not damaged
- Change the mandrel to one that is
not damaged, and/or to correct size
- Decrease the stroke settings
- Charge the battery, or replace
with a new one
- Select a blind rivet nut tool with
the correct capacity
Solution
Remove battery to reset
Remove battery to reset
Press and pull trigger
Remove battery to reset
Let tool cool down (+/-30 min)
Let tool cool down (+/-30 min)

3. Battery and Charger

3.1 Technical data
Battery
Weight lithium battery: 0.38 kg
Related voltage: 20V
Capacity: 2.0 Ah
Charger
Charger input voltage: 100-240VAC/50-60 Hz
Charging time: <60min
Output voltage: 20V
Weight: 0.37 kg
3.2 Battery charging and safety instructions
- Only charge batteries supplied by authorized dealers;
- Always use the original power supply intended for this tool;
- Before charging the battery, please read the warning label of the charger and the battery;
- Do not use a damaged charger for charging;
- Never attempt to charge a damaged battery;
- Never place a dirty or wet battery in the charger;
- Never dispose of batteries with household waste or in fire or water;
- Charger and lithium battery should not be placed in water, exposed to water, snow or any
type of wet environment;
- If the battery spills liquid, avoid contact; if there is any contact, rinse with water and see a
doctor immediately;
- The ambient temperature of charging and discharging is 0
- Long term storage of the battery (more than 3 months) must be placed at a temperature of
approx. 23 0 C with a max deviation of 5
NOTE: the battery is not fully charged when it leaves the factory.
In order to ensure the full function of the battery, fully charge it before using. Pay attention to
the charging indicator on the charger. Lithium charging can be charged at any time. Interrup-
tion of charging does not affect its life and will not damage the battery.
The battery is equipped with a temperature detection system.
Remove the battery:
The battery is equipped with a locking mechanism. When the battery is mounted on the
charger, it will be locked into it. If the battery is to be removed, press the unlock button and
slide the battery out of the charger. Do not disassemble.
Failure to comply with these instructions may result in explosions!
qonnect-fasteners.com
0 C up to max 40 0 C;
0 C.
- -
9