Chicago Pneumatic 3747 Mode D'emploi page 4

Safety Information
IC compliance Class B
CAN ICS-3(B)/NMB-3(B)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromet-
tre le fonctionnement.
FCC compliance Class B
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user's authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this de-
vice must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Responsible party:
Name: Mark Johnson
Position: General Manager
Address: Chicago Pneumatic Tool Company
LLC 1815 Clubhouse Road Rock Hill
SC 29730
USA
Mobile: +1 800 624 4735
Email: mark.johnson@cp.com
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gener-
ates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference
will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
▪ Reorient or relocate the receiving antenna.
▪ Increase the separation between the equipment and re-
ceiver.
▪ Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
▪ Consult the dealer or an experienced radio/TV techni-
cian for help.
4
Regional Requirements
WARNING
This product can expose you to chemicals including
lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For
more information go to
https://www.p65warnings.ca.gov/
Safety
Intended use
This product is intended to charge the following CP battery
packs only. No other use permitted. For professional use
only.
Model
CP18XP25
CP36XP25
Safety instructions
IMPORTANT
SAFETY IN-
STRUCTIONS
1
2
3
Battery tool use and care
• Recharge only with the charger specified by the man-
ufacturer. A charger that is suitable for one type of bat-
tery pack may create a risk of fire when used with an-
other battery pack.
• Use power tools only with specifically designated bat-
tery packs. Use of any other battery packs may create a
risk of injury and fire.
• When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
© Chicago Pneumatic - 8940176356
Part number
8940176067
8940176068
SAVE THESE
INSTRUCTIONS
This manual contains important safety and operating
instructions for battery charger CP ref. 8940176069.
Before using battery charger, read all instructions and
cautionary markings on battery charger, battery, and
product using battery.
CAUTION - To reduce risk of injury, charge only
rechargeable batteries defined on statement of use
from this manual. Other types of batteries may burst
causing personal injury and damage.
CHARGER