Before First Use - Gerlach Germany GL 7729 Mode D'emploi

convector in the event of excessive temperature convector (due to clogged vents, fan
malfunction ) . In this case, disconnect the unit from the power supply , waiting a few
minutes and remove the cause of overheating,
21. Do not touch the hot parts of the convector . Do not touch the appliance with wet hands.
22. In the case of wet convector or falling of any object through the ventilation grille of the
convector , turn it off immediately and disconnect from the network. Before re- use
with convector call for service .
23. Do not place the convector directly below the electrical outlet.
24. Always turn off the convector button before disconnecting it from the mains.
25. Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
26. Do not use this heater if it has been dropped
27. Do not use if there are visible signs of damage to the heater
28. Use the heater on a level and stable surface or attach it to the wall, if provided for by the
manufacturer
WARNING: Do not use this heater in small rooms where there are people who are unable
to leave them by themselves, unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at
least 1 m away from the heater air outlet.
"Caution Hot Surface" - The temperature of accessible surfaces may be higher when the equipment is in operation, which
means that the housing elements become hot during operation during operation, BE CAREFUL !!!
WARNING: In order to avoid overheating - do not cover the heater. The device is not to be covered with clothing, blankets
and other textile products which could cause ignition.

BEFORE FIRST USE

1. This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. The device cannot be used in
room smaller than space of floor 4m2.
DEVICE DESCRPTION (Figure 1)
1.LED screen
5.Tip-over switch
LED Screen (Fig. 2)
1A. Anti-frost function icon
1C. Low heating power icon
1E. Timer Icon
1G. ECO mode Icon
Control Panel (Fig. 3)
2A. ON/Stand-By Button
2C.Timer Button
2E. Oscillation Button
USAGE
1. Stand the device on flat, stable surface with 1 meter distance to any objects. Do not stand it on carpets. Switch off the Power switch (7)
to position "0" – off. Plug in the device to a 220-240V ~50/60Hz socket.
2.To start the device, press the power switch (7) located at the back of device to position "I" - on.
3.The power indicator (1F.) will be flashing.
4.Press the ON/Stand-by button (2A), your heater will working on Anti-frost function, at the same time, the anti-frost function icon (1A) will
light up. The temperature icon (1H) shows present temperature in room. This anti-frost mode keeps the room temperature at 7°C. It
means when room temperature is higher than 7°C, it works at fan mode, when the room temperature is lower than 7°C, it works at high
power of heating.
5. Press the mode button (2B) to select:
- fan mode by pressing once. Then the fan mode icon (1B) will be light up.
- lower heating power 750W by pressing again. Then the low power icon (1C) will be light up.
- high heating power 1500W by pressing again. Then the high power icon (1D) will be light up.
6. Press the timer button (2C), the timer icon(1E) will light up, and the twinkle sound appeared. Then press button (2G) to increase time or
(2F) to decrease time. You can select the working timer from 0 to 24 hours. The timer digital icon (1H) will shows the number you selected
to count down time to switch off the device automatically. After 5 seconds, the timer digital icon (1H) will show the room temperature
again.
7. Press the ECO button (2D), the ECO mode icon (1G) will light up. Under this function your heater will working in low heating power or
2.Control panel
6. Air inlet at back side
1B. Fan mode icon
1D. High heating power icon
1F. Power Indicator
1H. Temperature / Time digital icon
2B. Mode button (fan / low power / high power)
2D. ECO Button
2F. Temperature / Time Button
3.Air outlet
7. Power switch
2G. Temperature / Time Button
6
4.Base