Maintenance And Care; Hints For Use - Perles PB9-713 Mode D'emploi

Gear Change
With the selector desired speed can be selected.
1 = LOW SPEED: for screw driving, drilling large
diameters and for tapping threads
2 = HIGH SPEED: for drilling
The speed can be changed while tool is running under
no-load. It is recommended to change the speed when
the tool has completely stopped.
Hammer Selection PSB9, PSB9D
Hammer mode is selected by switching the selector
to the symbol corresponding to the user's choice
(hammer, or drilling).
All changes to the selection must be carried out after the
power tool has completely stopped.
The impact drilling has to be set on right hand rotation
when impact drilling.
Assembly and removal of tools
Keyless chuck
Lock the drill spindle by pressing the button
chuck sleeve firmly by hand and turn it for so long that
the chuck opening is big enough to insert a tool. Insert
the tool and fix it into the chuck by turning the sleeve in
the reverse direction. For removing the tool, lock the drill
spindle by pressing the button
in the opposite direction than in the assembly procedure.
Self-tightening drill chuck
Self-tightening drill chuck tightens itself additionally under
load, and thus prevents the tool from slipping. Lock the
drill spindle by pressing the button
tool. Hold the chuck sleeve firmly by hand and turn it for
so long that the chuck opening is big enough to insert a
tool. Insert the tool, and fix it into the chuck by turning the
front sleeve . Turn the front sleeve in the direction of
LOCK in order to prevent it from loosening.
For removing the tool, lock the drill spindle by pressing
the button . Turn the middle sleeve
or RELEASE direction. Release the tool by turning the
front sleeve in the opposite direction than in the
assembly procedure.
The spindle can be locked by pressing the button
by firmly holding the rear sleeve of the drill chuck C.
Three-jaw chuck
Press the spindle-locking button
Insert the accessory as deep as possible in the chuck.
Do not use accessories with a damaged shank.
Clamp evenly in all three holes with the chuck key
Unscrewing chuck
Chuck is tightened with high torque. In case of chuck
change send the tool to a Perles authorized service
centre for repair.
Auxiliary handle
!
Operate the machine only with the auxiliary handle
The auxiliary handle
secure and low-fatigue working posture.
The drilling depth can be set with the depth stop

HINTS FOR USE

Use only correctly sharpened drill bits, which are
suitable for the material being drilled.
. Hold the
. Turn the chuck sleeve
in order to insert a
in the UNLOCK
inwards
can be set to any position for a
To drill hard materials, fi
power tool. However,
improve
pressure on the tool and its bit.
After longer periods of working at low speed, allow the
machine to cool down by running it for approx. 3
minutes at maximum speed with no load.

MAINTENANCE AND CARE

Unplug the tool from the socket before
performing any works on the tool!
Tool requires no special maintenance, bu
time you must control the parts that are submitted to
wea r-and-tear under normal operating conditions. This
in clu des the control and replacement of carbon
brushes and grease in reducing gear housing. Take
the tool to an authorized service centre.
Keep the tool and supply cord clean. Keep ventilation
slots clean and open. Wipe the surface of the tool with
a soft cloth!
!
It is not allowed to use household cleaning agents
that contain petrol, trichloroethylene, ammonia
and chlorides. These substances corrode and
damage plastic parts of the tool.
Excessive sparking generally indicates the presence
of dirt in the motor or abnormal wear on the carbons.
!
In case of electric or mechanical failure, send the
tool to a Perles authorized service centre for
repair.
SERVICING AND REPAIRS
If servicing is required, contact one of our listed service
cent ers. It
individual work on the tool.
!
Have the tool repaired by authorized p
!
Any repairs of the tool in unauthorized service
centers is performed at own responsibility.
!
The owner of the tool is responsible for all works
on the tool that were not performed in authori
service centers, and therefore he looses the claim
for guarantee.
or
WASTE DISPOSAL AND
ENVIRONMENT PROTECTION
.
11
rm pressure is required on the
excessive pressure does not
performance and
is not allowed and dangerous to perform any
The machine, accessories
should be sorted for env
recycling.
:
Only for EC countries
!
Do not dispose of power tools into
!
household waste
According the European Guideline 2002/
for Waste Electrical and
and its implementation into national right, power
tools that are no longer usable must be
collected separately and disposed of in an
environmentally correct manner
places unnecessary
t after some
ersons.
zed
and packaging
ironmental-friendly
96/EC
Electronic Equipment