Product Familiarisation; Accessories - SilverCrest 264219 Mode D'emploi

GB

Product Familiarisation

1
Mixing Paddle
2 Attachment Point
3
Output Drive
4
Handles
5
On/Off Trigger Switch
6
Lock-On Button
7 Motor Vents
8 Variable Speed Dial
Included accessories (not shown):
1x Spare carbon brushes, spanner
Intended Use
Handheld electric paddle mixer used for the preparation of plaster, cement,
levelling compounds, emulsions and similar building and decorating
materials.
Unpacking Your Tool
• Carefully unpack and inspect your new sander. Familiarise yourself with
all its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply before
attaching or changing any accessories, or making any adjustments.
Attaching a mixing paddle
WARNING: Always disconnect from the power supply before attaching/
changing accessories.
WARNING: Never fit any attachment with a maximum speed lower than the
no load speed of the machine.
• This plaster mixer is equipped with an M14 female Output Drive (3)
• M14 threaded mixing paddles are fitted by screwing them into the output
drive. Tighten with a suitable spanner
• Ensure that the mixing paddle is securely tightened before use
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing
protection, as well as suitable gloves, when working with this tool.
Switching On and Off
WARNING: Always ensure that the power cord is not interfering with the
mixing paddle or presenting a tripping hazard for the operator or other
personnel in the vicinity.
• Grip the mixer firmly by the Handles (4), with both hands
• To start the mixer, press the On/Off Trigger Switch (5)
• Press the Lock-On Button (6) to lock the tool in the 'on' position
• To stop the mixer, squeeze the on/off switch and release
Speed selection
• The mixer is fitted with variable speed control
• To alter the speed, simply adjust the Variable Speed Dial (8). The higher
the number, the faster the speed
6 6
Mixing of material
WARNING: ALWAYS wear adequate personal protection equipment when
mixing compounds, including safety goggles or a face shield, breathing
protection (specific to the material used), gloves (suitable for the material
used), hearing protection, and a hard hat where required.
WARNING: This tool is designed for two-handed operation. Never use with
one hand, or attempt to mount stationary or prop-up against another object.
Note: ALWAYS refer to the compound manufacturers mixing requirements
and recommendations.
• The shape and size of a mixing paddle that is ideal for a specific
application will depend on the type of material being mixed:
° Substances with a low viscosity such as dispersion paint, varnish,
thinset, sealing and levelling compounds, cement, grout etc., will
require a mixing paddle with a left-hand twist
° Substances with a high viscosity, such as ready-mixed plaster,
concrete, screed, putty and epoxy resin, will require a mixing paddle
with a right hand twist
• It is important to keep the paddle moving throughout the bulk of the
material whilst mixing, as opposed to keeping it in one central position in
the mixing container. Mix until compound is completely blended
WARNING: DO NOT overload the motor whilst mixing. When you recognise
a significant drop in speed, switch off immediately to avoid damage to the
tool. Consider changing to a different mixing paddle or accessory more
suitable for the material.
WARNING: When you have completed the mixing procedure, allow the
mixer to come to a complete stop before lifting it out of the material. Make
sure not to contaminate the environment and clean-up potential spillage.
WARNING: To avoid damage to the machine and cross-contamination
between different materials, always clean the mixing paddle immediately
after use. Don't let the material dry on the accessory. Also, refer to the
paragraph 'Cleaning' in the 'Maintenance' section below.

Accessories

• A range of accessories for your tool, including mixing paddles in
numerous sizes and for different compounds, is available from your
Silverline stockist. Spare parts can be obtained from toolsparesonline.
com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out
any inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre.
This advice also applies to extension cords used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine's service life. Clean the body of
your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do
not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
• Use water, a suitable cleaning solution, or mild solvent to clean rests of
material off the accessory. Wear appropriate protection equipment whilst
cleaning, including eye, hand and breathing protection
Note: Dispose of rest material and contaminated cleaning solution
according to regulations. Recycle where possible. Only use non-water
solvents where absolutely necessary and always follow the manufacturer's
guidelines for safe usage.
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable
spray lubricant