K Source VS8 Guide D'utilisation

Important: Read this manual carefully before
installation and usage. Also retain this for future
reference.
Dear customer,
Thank you for choosing the Vision System back-
up camera system. This system is designed to
reduce the blind spot behind your vehicle and
helps you operate your vehicle safely.
Note: We suggest professional installation on this
product since the automotive camera/monitor
installation can be difficult at times. We also suggest
you read our warranty information carefully before
you start the installation. We require you to mail in
the warranty card along with the proof of purchase
in order to honor our standard 90 days warranty on
this product.
Parts list:
- Mirror head with monitor
- Camera cable 18ft (550cm)
- Power cable 13ft (400cm)
- VSC800 Camera
- Windshield mounting plate
- Tap-in squeeze connectors (3)
- Wire ties (5)
- Installation instructions
Installation Instruction
1. Inspect the Vision System rear view mirror for
damage or defects.
2. Prior to disconnecting the negative side of the
battery terminal, be sure to record the security code.
The code is to be re-entered after reconnecting the
negative battery terminal. Your vehicle may be
equipped with an anti-theft radio.
Rear View Monitor Mirror Installation
1. Remove the original equipment (OEM) rear view
mirror.
2. The Vision System rear view mirror is engineered to
fit the majority of existing (OEM) mounting plates.
3. If the Vision System mirror does not fit on the
existing mounting plate, use the mounting plate
provided. There are several choices of rear view
mounting glues you can purchase from your local auto
parts stores. Below are a few examples.
3M #08752
VersaChem #11109
Permatex #81840, #81844
4. Do not attempt to remove the existing mouting
plate by prying it with a screwdriver or with a sharp
instrument. That could crack the windshield. Leave
the mounting plate on and mount the Vision System
mounting plate either on the side, top or bottom of
the existing mounting plate.
Vision System
Back-up Camera and Monitor System
OWNER'S MANUAL
5. Slide the Vision System mirror base over the
mounting plate and tighten the screw on the mirror
mounting bracket until the mirror is snug on the
mounting plate.
6. Connect both wire harnesses to the Vision System
mirror. Route wire harness up to the headliner. Use
your fingers or a nylon tool to tuck the wire harness
snugly between the headliner and the roof. Route the
wire harness on the drivers or passengers side pillar
and under the dash.
7. Route the red, white and black wires toward the
fuse panel. The fuse panel is usually located under the
dashboard on the driver side.
8. Tap the red 12V DC power cable to a "Switched"
(hot only when the ignition is keyed) power source.
9. The black ground cable can be attached to a bolt,
screw or wire that contacts the bare metal of your
vehicle's chassis. Look for an existing bolt or screw
in your vehicle that appears to make contact with the
chassis. Loosen it, slip the ground wire underneath
then tighten it up. (If your ground wire doesn't
contact bare metal, your mirror won't operate)
10. The white cable needs to be attached to a reverse
signal or switch. The most common place to find a
reverse signal is directly from your rear reverse bulb
circuit or at the neutral safety switch sometime found
attached to the transmission or steering column.
11. Route the camera wiring harness toward the
rear of the car to the inside of the trunk. The cables
will need to be passed to the outside of the vehicle
and will need to be connected to the camera at the
license plate.
Camera Installation
1. Loosen the license plate mounting bolts and
remove the rear license plate.
2. Choose a routing path for the camera's power cable
and video cable through the vehicle's body to the rear
of the vehicle. Some vehicles have a hole to pass the
wire through. If no hole found, you may need to drill
a half inch diameter hole. Make sure that there is
nothing behind the drilling location.
3. Pass the camera and electrical wires through
the hole
4. Slide the camera mounting bracket over the top
of the license plate and align the right side license
mounting hole and the camera bracket mounting hole.
5. Tighten all license plate bolts to secure the license
plate and the camera
6. Adjust the camera angle
7. Connect the cables to the camera receptacle and
tape the connectors with electrical tape to keep the
moisture and water out and keep it from getting rust
or water damage.
Model No. VS8
Key Features
1. Brightness Adjustment:
For a clear view, the monitor brightness can
be adjusted using toggle switch located at the
bottom of the mirror housing.
2. On/Off Switch:
The ON/Off switch is located at the front center
of the Vision System mirror housing.
The monitor is ON mode when the switch is in
the IN position even if the car is not in reverse.
When the switch is in the OUT position, it is in
STANBY mode displaying no image until the car
is placed in reverse.
Monitor Specification
Item Specification
Screen Size 3.5" diagonal
Backlight Type LED
Operating Voltage 9~16 V
Supply Current
200~500mA
(with camera)
Video Format NTSC
225nit (MIN.)
luminance(after mirror)
(immediately)
Display Format 960×240 Dot
Screen Resolution 230, 400 Dots
Dot Pitch 0.073(W)×0.219(H)
Visible display size 2.71"×2.02"<inch>
Work Temperature -20°C~70°C
Storage Temperature -30°C~80°C
Horizontal Viewing Angle 120° (MIN.)
Contrast Ratio 400 (MIN.)
Vertically Viewing Angles 90° (MIN.)
Camera Specification
Sensor 1/4" CMOS Color Sensor
Effective pixels 510 * 492 pixels
Video System NTSC
Video Out 1.0Vp-p, 75Ω
Resolution 380 TVL
Minimum Illumination 3 LUX / F1.2(0LUX with LED)
S/N Ratio More than 48 dB
Current Consumption No more 150mA
Gain Control AGC
Operation Temp -20°C to 60°C
Storage Temp -30°C to 60°C
Optical View Angle FOV=120°
Camera View Angle 88° horizontal, 80° vertical