Technical Data - SAN MARCO SMP214 Mode D'emploi

EN
Backwash
it is time to backwash when the pressure gauge rises
0,3 to 0,6 bar above what it normally reads when the
In this position, the water is fed in at the bottom soil
Closed
Function: Cleaning the hair and lint strainer. This posi-
CAUTION: Do not run pump with valve in this position.
Purge/
Drain vacuuming pools with large amounts of debris or after
an algae treatment. In this position, water bypasses
the waste line.
Winterize Function: winterizing and storage. In this position,
the valve lever is between positions which removes
pressure from internal valve components for winter
(off-season) storage.
CAUTION: Do not run pump with valve in this position.
Filtering time
to 5 times in a 24 hour period, depending on the load and the size of the
system and the size of the swimming pool. However, we recommend a
minimum running time of 12 hours per day.
Power source Instructions
cable, which may only be connected to a circuit with a residual current
circuit breaker (RCCB) with a rated residual current of no more than
30mA.

Technical data:

■ Circulation power 3,800 l/h
■ Pump is not self-priming
■ maximum water temperature 35 °C
■ 230 V / 200 W
■ 7 way valve with pressure gauge
■ Tank Ø 250 mm
■ Connector Ø 32/38 mm
■ Ground plate
■ requires approx. 10 kg sand
■ recommended grain size 0.7 - 1.2 mm
■ for pools up to 19,000 l capacity
■ Available separately: Speedpart container for UV System Speed UV
Operation with a pool vacuum cleaner
(Illustration 8)
■
system's suction pipe. In doing so, the pool vacuum cleaner's hose
■
■ Please observe the pool vacuum cleaner's operating instructions. To
■ Please select the "FILTERN" position on the valve head.
■ Alternatively, you can also select the "ENTLEEREN (empty)" position,
for example if algae forms in the pool. Dirty pool water will not then run
back into the pool, but will be directly channelled away via the waste pipe.
correct level after cleaning, if necessary.
pagina 10 di 18
Problem treatment
Cause of Problems
Sand contaminated with dirt
Pump sucks air
(Bubbles at the inlet)
Skimmer or pump gets too little
water
Skimmer basket contaminated
contaminated
For any errors not listed above, please contact your dealer!
Important Note
To winterize the system
■ Unplug the pump from the power source.
■
and return ports.
■
hoses.
■ Place the handle on the central valve in position 'Winterize' to relieve
the tension on the spring and internal valve components.
Care instructions
is not true for algae, bacteria and other microorganisms, which are
also a constant threat to clear, clean and healthy pool water. For their
prevention or removal, special water treatment is available, properly and
permanently dosed, guarantee for swimmers any kind of harassment
and ensure proper hygienic bath water.
Cleaning
Use conventional cleaning products. Do not use solvent-based or abra-
sive cleaning agents/tools, i.e. no hard sponges, brushes etc..
Storage
The product must be thoroughly dried after cleaning. After which, it is to
be stored in a dry location protected from frost.
Disposal
Disposing of packaging: The packaging material has been selected
in view of environmental concerns and disposability and is therefore
recyclable. The paper and cardboard can be recycled, as can the plastic
coverings.
Disposing of the product: Applicable in the European Union and
other European states with systems in place for collecting and sorting
recyclable materials. Dispose of the product in accordance with any
laws and regulations applicable at your place of residence.
Warranty conditions
The respective country's legal provisions for warranty conditions shall
apply accordingly.
Solution
Backwashing (cleaning of the
sand)
defective hoses,
tighten hose clamps
Check water level and increase
if necessary, check the intake for
dirt accumulation
Cleaning of the skimmer basket
FILTRO A SABBIA
SMP214