VESTEL VEB34116 Notice D'utilisation page 37

MINUS " " sensor buttons on the side of
the display. The temperature can be
adjusted within the range of 50°C to 275°C.
After the desired function has been
selected, and the temperature and time are
set, touch the PLAY/PAUSE " " sensor to
start the oven function operation. While the
oven is operating, the play/pause button
brightens during the cooking time.
Adjusting the Time of Day
When the oven has been installed, the
time of day must be set according to the
following instructions.
Touch the ON/OFF " " sensor to switch the
oven on and enter "WAIT" mode. During
this mode, touch the MODE " " sensor
button until the time is selected. You can
adjust it using the PLUS "
" sensor buttons. To complete the time
adjustment, touch the MODE " " sensor
once again.
The time will only have to be set again if the
appliance is disconnected from the power
supply for a long period of time.
Adjusting the Cooking Time
The cooking time can be adjusted during
"WAIT" mode or during "OPERATING"
mode.
Adjusting the Minute Minder " "
Touch the MODE " " sensor until the
Minute Minder symbol illuminates on the
Time display and "00:00" appears. Adjust
the desired time period for the warning
signal using the PLUS "
sensor buttons while the symbol is flashing.
When you have completed the adjustment,
do not press any buttons for a few seconds,
then the Minute Minder timer will be set.
When the timer reaches zero, an audible
warning will sound, and the Minute Minder
symbol and "00:00" will flash on the
Time display. Press any button to stop
the audible warning and the symbol will
disappear.
Adjusting the Cooking Duration Time
This function helps you to cook for a fixed
period of time. Prepare the food for cooking
and put it in the oven. Then, select the
desired cooking function and
the temperature. Touch the MODE " "
sensor button until you see the Duration
Time symbol " " on the Time display. Set
the required cooking period using the PLUS
" and MINUS " " sensors while the timer
"
is in this position. When you have
" and MINUS "
" and MINUS " "
EN - 15
completed the adjustment, wait until the
current time of day is displayed and the
Duration Time symbol remains illuminated.
When the timer reaches zero, the oven will
switch off, an audible warning will sound
and the Duration Time symbol will flash on
the Time display. Touch any sensor on the
control unit to end the sound.
Adjusting the Cooking End Time
This function is used to begin cooking after
a certain period of time and for a specific
duration of time. Prepare the food for
cooking and put it in the oven. Then,
select the desired cooking function and the
temperature.
Touch the MODE " " button until you see
the Cooking Duration Time symbol on the
Time display. Set the required cooking
period using the PLUS "
sensor while the timer is in this position.
When you have completed the adjustment,
wait until the current time of day is
displayed and until the Cooking Duration
Time symbol remains illuminated.
Then, touch the MODE " " sensor button
until you see the Cooking End Time symbol
on the Time display. The time of day and
the Cooking Duration Time symbol will
flash. Set the required finish time using the
PLUS " " and MINUS " " sensors while
the timer is in this position. When you have
completed the adjustment, wait until the
current time of day is displayed and until
the Cooking End Time symbol "
remains illuminated.
The oven will calculate the operating time
by deducting the cooking period from
the set finishing time, at which it will stop
operating. The timer will give an audible
warning and the Cooking End Time symbol
will flash. Touching any button on the timer
will end the audible warning.
Digital Timer Sound Adjustment
To alter the warning signal sound, while the
Time display shows the time of day, press
and hold the THERMOSTAT " " sensor
button for 3 seconds until there is an
audible signal sound. After this, each time
the MINUS " " OR PLUS "
pressed, a different signal will sound. There
are four different types of signal sound.
Select the desired sound and do not press
any other buttons. After a short time, the
selected signal sound will be saved.
Boost Function
This function is used to shorten the
" and MINUS " "
"
" sensor is