Before Use; Temperature Selection - Taurus Alpatec MSB 2000 Manuel D'instructions

D Timer button
E Open window detector
F OK button
G Heater setting
ASSEMBLING THE WALL BRACKET:
- The appliance has a wall support (Fig.1) to
support the product.
- Fix the wall support as you think appropriate,
using wall plugs, screws, adhesive...
- Taking into account the separation distances
mentioned above, place the wall support in the
required position and mark the drilling points on
the wall (Fig.2).
- Drill on the marks and introduce the plugs
(Fig.3).
- Fit the support, lining up its holes with those of
the plugs, and screw on (Fig.4).
- Make sure that the bracket is firmly fixed; it
should be able to support twice the weight of the
appliance.
- Fit the appliance into the wall support.
- Now follow the instructions in Figures 5,6,7.
INSTRUCTIONS FOR USE

BEFORE USE:

- Make sure that all the product's packaging has
been removed.
- Some parts of the appliance have been lightly
greased, consequently, the appliance may give
off a light smoke the first time it is used. After a
short time, this smoke will disappear.
- To eliminate the smell given off by the appliance
when used for the first time, it is recommended
to have it on at full power for 2 hours in a well-
ventilated room.
- Prepare the appliance according to the function
you wish to use.
USE:
- Connect the appliance to the mains.
- Turn the appliance on using the on/off switch(a)
- Turn the appliance on using the on/off button.
(B)
HEATER FUNCTION
- Select the heater function by pressing (G) and
select the desired setting: 1800W ( ), 900W
( ) or fan function.
- Check that the thermostat control is set to the
desired temperature.

TEMPERATURE SELECTION

- Select the desired temperature (5-40ºC) by
pressing (A).
- Press (C) to set the desired temperature and
then press (F) to confirm.
SET DAY & TIME:
- When setting the day and time, the unit has to
be in standby mode.
- Press (A) and the icons
up, use + or – to set the day, once the required
day is flashing, press (F) to confirm it.
- Press (A) until the hour icon lights up
order to set the hour, and then OK to confirm it.
- Press (A) until the minute icon lights up
in order to set the minutes, and then OK to
confirm it.
TIMER:
- Withy trhe unit in nstandby, press and hold (D)
for 3 seconds , the icon
programming has been completed.
1 2 3 4 5 6 7
- The icon will light up fully, now use
+ or – to select the desired day of the week,
once selected press OK to confirm. Next, the
icon will appear in order to
1 6 12 18
select when the heater is operating, one mark
per hour, use + or – to select the desired hours
and press OK (F) to confirm.
- To program more than one hour, use + or – for
the ON time, press OK (F) to confirm, and then
press SET (A) to program the OFF time, use +
or – and OK (F) to confirm.
- Once finished, the temperature can be set, 20°
by default, use + or – to specify the desired
temperature (5-40) and OK (F) to confirm.
- In this way the whole week, 7 days, can be
programmed.
- When the weekly programming is operational,
the icon will be lit, to switch this off, or on
again, press (D) and the icon will disappear or
reappear.
TOWEL WARMING FUNCTION
- Press (E) to switch on the towel warming
function. To cancel this function, press the same
button again.
- During operation, the icon
- The towel warmer is 200W.
OPEN WINDOW DETECTOR:
- Press and hold (E) for 3 seconds to activate or
deactivate this function.
1 2 3 4 5 6 7
will light
in
will remain lit until
will light up.